{"title":"Automotive \u0026 Transport","description":"","products":[{"product_id":"nextite-ab210","title":"NEXTITE AB210 High Strength Medium Cure","description":"\u003cp\u003eNEXTITE AB210 (formerly ACRI-BOND 210) delivers high strength and dependable performance when bonding plastics, metals and composites with minimal surface preparation. It provides a high strength bond with a medium working time of 14-17 minutes, making it ideal for structural and general assembly applications. The thicker viscosity allows for easy, controlled application across a wide range of materials.\u003c\/p\u003e\n\u003ch3\u003eProduct Overview\u003c\/h3\u003e\n\u003cp\u003eNEXTITE AB210 is a high-performance, two-part methyl methacrylate (MMA) structural adhesive engineered for demanding bonding applications. Designed for fast, reliable bonding of engineering plastics, metals, and composite materials, NEXTITE AB210 offers exceptional strength, durability, and ease of use.\u003c\/p\u003e\n\u003cp\u003eWith a medium working time of 14 to 17 minutes, this adhesive allows for efficient assembly without the need for extensive surface preparation or primers. It is particularly suited for bonding thermoplastics, powder-coated metals, raw metals, and composite assemblies where high strength and impact resistance are critical.\u003c\/p\u003e\n\u003cp\u003eNEXTITE AB210 delivers rapid strength development at room temperature, along with excellent toughness, fatigue resistance, and long-term durability. Its non-sag, thixotropic formula makes it ideal for precise application, even on vertical surfaces. It also provides some gap filling capabilities of up to around 4mm. This adhesive is the go-to solution for industrial manufacturing, plastic fabrication, transportation, signage, and general assembly where consistent performance and structural integrity are required.\u003c\/p\u003e\n\u003cp\u003eFor production environments where faster fixture times are critical, NEXTITE AB200 offers the same performance and material compatibility as NEXTITE AB210 but with a reduced working time of 4 to 6 minutes and a fixture time of 14 to 17 minutes.\u003c\/p\u003e\n\u003ch3\u003eApplications and Uses\u003c\/h3\u003e\n\u003cp\u003eNEXTITE AB210 bonds to a variety of substrates they include but aren’t limited to:\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003ePlastics: Acrylic (PMMA), Polycarbonate (PC), Acrylonitrile Butadiene Styrene (ABS), Polyvinyl Chloride (PVC)\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003eMetals: Aluminium, Steel, Stainless Steel, Powder Coated Surfaces\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003eComposites: Fibreglass Reinforced Plastic (FRP), Carbon Fibre (CF)\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003eOther: Glass, Concrete, Wood, MDF\u003c\/p\u003e\n\u003cp\u003eNEXTITE AB210 will not adhere to plastics with a low surface energy such as Polypropylene (PP), Polyethylene (PE) or Polyolefins. These plastics can be structurally adhered to with NEXTITE AB206 and NEXTITE Cyanoacrylates also have a great bond when using NEXTITE SP 901 Primer.\u003c\/p\u003e\n\u003ch5\u003eSome applications of NEXTITE AB210 include:\u003c\/h5\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003eTransport Industry: Used to bond fibreglass (FRP), metal, and composites in vehicles like trucks, buses, trailers, and railcars.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003eMarine: Bonds composite hulls, decks, and marine components with strong resistance to moisture and saltwater.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003eConstruction: Joins panels, facades, and modular building elements where strength and quick curing are critical.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003eSignage and Displays: Bonds plastic, metal, and composite parts in signs and displays for indoor and outdoor use.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003eIndustrial Equipment: Used in machinery and appliance assembly for strong, impact- and vibration-resistant joints.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003eAutomotive: Bonding structural or cosmetic repair of body panels, including re-bonding fibreglass or composite components.\u003c\/p\u003e\n\u003ch5\u003eVersatility of NEXTITE AB210\u003c\/h5\u003e\n\u003cp\u003eWhile bond strength is important, it’s not the only factor to consider when selecting an adhesive. Once fully cured, NEXTITE AB210 delivers a range of additional benefits that can make a real difference depending on your application. \u003c\/p\u003e\n\u003cp\u003eWhen fully cured NEXTITE AB210 can be sanded, grinded, routed and polished to get your desired finish. You can even paint over it!\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003eGreat Chemical Resistance\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003eHigh resistance to weathering\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003eCan be used in indoor and outdoor applications\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003eWaterproofing when applied correctly\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003eHigh Temperature resistance -40 to 140°C\u003c\/p\u003e\n\u003ch3\u003eTools and Accessories\u003c\/h3\u003e\n\u003cp\u003eNEXTITE AB210 requires the use of a compatible dual cartridge dispensing applicator and static mixer nozzles, sold separately. Both the 50mL and 400mL Cartridges use standard 1:1 Ratio dual cartridge dispensing applicators and static mixers. It is important to use the correct applicator and mixer for each cartridge size, as 1:1 ratio systems are not compatible with other ratios cartridges and accessories. Each cartridge type requires the matching dispensing applicator and static mixer designed specifically for its ratio.\u003c\/p\u003e\n\u003ch5\u003e50mL Tubes\u003c\/h5\u003e\n\u003cp\u003eDispensing Applicator: Manual 50mL 1:1 Dispensing Applicator | Manual Hand Plunger for 1:1 50mL Cartridges (for one time use)\u003c\/p\u003e\n\u003cp\u003eStatic Mixer Nozzles: 1:1 50mL Quadro B Type (Standard Tip) | 1:1 50mL Quadro B Type (Narrow Tip) \u003c\/p\u003e\n\u003ch5\u003e400mL Tubes\u003c\/h5\u003e\n\u003cp\u003eDispensing Applicator: Manual 400mL 1:1 Dispensing Applicator | Pneumatic 400mL 1:1 Dispensing Applicator | Electric 400mL 1:1 Dispensing Applicator\u003c\/p\u003e\n\u003cp\u003eExtra Static Mixer Nozzles: 1:1 400mL Quadro F Type (Green – White Base)\u003c\/p\u003e\n\u003ch3\u003eTechnical Highlights\u003c\/h3\u003e\n\u003cdiv data-table=\"58841\" class=\"TablePress\"\u003e\u003cbr\u003e\u003c\/div\u003e\n\u003ch3\u003eStrength Tests\u003c\/h3\u003e\n\u003cdiv class=\"TablePress\" data-table=\"58842\"\u003e\u003cbr\u003e\u003c\/div\u003e\n\u003cp style=\"line-height: 150%;\" class=\"MsoNormal\"\u003e\u003cspan style=\"font-size: 10.0pt; line-height: 150%; font-family: 'Arial',sans-serif;\"\u003e** SF, AF, CF – determine how the substrate failed.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp style=\"text-indent: -18.0pt; line-height: 150%; mso-list: l0 level1 lfo1;\" class=\"MsoListParagraphCxSpFirst\"\u003e\u003c!-- [if !supportLists]--\u003e\u003cspan style=\"font-size: 10.0pt; line-height: 150%; font-family: 'Arial',sans-serif; mso-fareast-font-family: Arial;\"\u003e\u003cspan style=\"mso-list: Ignore;\"\u003e-\u003cspan style=\"font: 7.0pt 'Times New Roman';\"\u003e        \u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c!--[endif]--\u003e\u003cspan style=\"font-size: 10.0pt; line-height: 150%; font-family: 'Arial',sans-serif;\"\u003eSF – Substrate Failure\u003c\/span\u003e\u003c\/p\u003e\n\u003cp style=\"text-indent: -18.0pt; line-height: 150%; mso-list: l0 level1 lfo1;\" class=\"MsoListParagraphCxSpMiddle\"\u003e\u003c!-- [if !supportLists]--\u003e\u003cspan style=\"font-size: 10.0pt; line-height: 150%; font-family: 'Arial',sans-serif; mso-fareast-font-family: Arial;\"\u003e\u003cspan style=\"mso-list: Ignore;\"\u003e-\u003cspan style=\"font: 7.0pt 'Times New Roman';\"\u003e        \u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c!--[endif]--\u003e\u003cspan style=\"font-size: 10.0pt; line-height: 150%; font-family: 'Arial',sans-serif;\"\u003eAF – Adhesion Failure\u003c\/span\u003e\u003c\/p\u003e\n\u003cp style=\"text-indent: -18.0pt; line-height: 150%; mso-list: l0 level1 lfo1;\" class=\"MsoListParagraphCxSpLast\"\u003e\u003c!-- [if !supportLists]--\u003e\u003cspan style=\"font-size: 10.0pt; line-height: 150%; font-family: 'Arial',sans-serif; mso-fareast-font-family: Arial;\"\u003e\u003cspan style=\"mso-list: Ignore;\"\u003e-\u003cspan style=\"font: 7.0pt 'Times New Roman';\"\u003e        \u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c!--[endif]--\u003e\u003cspan style=\"font-size: 10.0pt; line-height: 150%; font-family: 'Arial',sans-serif;\"\u003eCF – Cohesive Failure\u003c\/span\u003e\u003c\/p\u003e\n\u003ch3\u003eChemical Resistance\u003c\/h3\u003e\n\u003cdiv data-table=\"58843\" class=\"TablePress\"\u003e\u003cbr\u003e\u003c\/div\u003e\n\u003ch3\u003eInstructions for use\u003c\/h3\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e1.     \u003c!--[endif]--\u003eUse a static mixer nozzle to accurately mix the contents of the 1:1 cartridge. Each cartridge includes one Static Mixer Nozzle Green 1:1, and you can purchase more in 5, 10 and 50 packs from our store.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e2.     \u003c!--[endif]--\u003eYou will also require a 1:1 Static Mixing Dispenser to push the contents through the static mixer. This is the best way to apply it and get accurate, dependable results every time.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e3.     \u003c!--[endif]--\u003eParts to be joined should fit without forcing and be clean, it is recommended to use NEXTITE PROPREP prior to applying any product to remove any oils, dust and dirt. It is important to let out any air bubbles and ensure adhesive is fully mixed by dispensing the first part of the cartridge onto some paper. This is to make sure the two separate parts are fully mixed and is generally the first 2-3mL. Apply adhesive directly from the static mixer.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e4.     \u003c!--[endif]--\u003ePress parts together in firm contact and use a clamp to secure while the glue reacts. NEXTITE AB210 will achieve a working strength within 30-36 min and full cure strength within 24 hours. You have approximately 14-17 minutes to work with the glue before it starts to set off.\u003c\/p\u003e\n\u003cp\u003ePlease check the TDS for material suitability and strength of each bond. For a tutorial how to use please refer to our YouTube Chanel.\u003c\/p\u003e\n\u003ch3\u003eShelf Life, Storage and Pack Size\u003c\/h3\u003e\n\u003cp\u003eNEXTITE AB210 has a 12 Month Shelf Life when stored correctly.\u003c\/p\u003e\n\u003cp\u003eStore in a cool dry place out of direct sunlight, an enclosed cabinet is recommended, to extend the shelf life of this product. Keep the open container tightly closed do not leave open. \u003c\/p\u003e\n\u003cp\u003e50mL and 400mL Cartridges as well as 20kg Pails and 200kg Drums for high volume use.\u003c\/p\u003e\n\u003ch3\u003eDownloads\u003c\/h3\u003e\n\u003cp\u003eNEXTITE AB210 Technical Data Sheet | NEXTITE AB210 Material Safety Data Sheet\u003c\/p\u003e","brand":"NEXTITE","offers":[{"title":"50mL \/ Beige","offer_id":46409535586453,"sku":"AB210-50","price":34.15,"currency_code":"AUD","in_stock":true},{"title":"50mL \/ Black","offer_id":46740051984533,"sku":"AB210B-50","price":34.15,"currency_code":"AUD","in_stock":true},{"title":"400mL \/ Beige","offer_id":46409535619221,"sku":"AB210-400","price":116.8,"currency_code":"AUD","in_stock":true},{"title":"400mL \/ Black","offer_id":46740052017301,"sku":"AB210B-400","price":116.8,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0740\/9834\/4085\/files\/NEXTITEAB21050mL_dcd1d348-feef-4c22-b8ab-2e88ff566501.jpg?v=1770618933"},{"product_id":"nextite-ab200","title":"NEXTITE AB200 High Strength Fast Cure","description":"\u003cp\u003eNEXTITE AB200 delivers high strength and dependable performance when bonding plastics, metals and composites with minimal surface preparation. It provides a high strength bond with a short working time of 4-6 minutes, making it ideal for structural and general assembly applications. The thicker viscosity allows for easy, controlled application across a wide range of materials.\u003c\/p\u003e\n\u003ch3\u003eProduct Overview\u003c\/h3\u003e\n\u003cp\u003eNEXTITE AB200 is a high-performance, two-part methyl methacrylate (MMA) structural adhesive engineered for demanding bonding applications. Designed for fast, reliable bonding of engineering plastics, metals, and composite materials, NEXTITE AB200 offers exceptional strength, durability, and ease of use.\u003c\/p\u003e\n\u003cp\u003eWith a short working time of 4 to 6 minutes, this adhesive is perfect for production lines that need a fast cure. It allows for efficient assembly without the need for extensive surface preparation or primers. It is particularly suited for bonding thermoplastics, powder-coated metals, raw metals, and composite assemblies where high strength and impact resistance are critical.\u003c\/p\u003e\n\u003cp\u003eNEXTITE AB200 delivers rapid strength development at room temperature, along with excellent toughness, fatigue resistance, and long-term durability. Its non-sag, thixotropic formula makes it ideal for precise application, even on vertical surfaces. It also provides some gap filling capabilities of up to around 4mm. This adhesive is the go-to solution for industrial manufacturing, plastic fabrication, transportation, signage, and general assembly where consistent performance and structural integrity are required.\u003c\/p\u003e\n\u003cp\u003eFor production environments where medium working times are critical, NEXTITE AB210 offers the same performance and material compatibility as NEXTITE AB200 but with an increased working time of 14 to 17 minutes and a fixture time of 30 to 36 minutes.\u003c\/p\u003e\n\u003ch3\u003eApplications and Uses\u003c\/h3\u003e\n\u003cp\u003eNEXTITE AB200 bonds to a variety of substrates they include but aren’t limited to:\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003ePlastics: Acrylic (PMMA), Polycarbonate (PC), Acrylonitrile Butadiene Styrene (ABS), Polyvinyl Chloride (PVC)\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003eMetals: Aluminium, Steel, Stainless Steel, Powder Coated Surfaces\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003eComposites: Fibreglass Reinforced Plastic (FRP), Carbon Fibre (CF)\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003eOther: Glass, Concrete, Wood, MDF\u003c\/p\u003e\n\u003cp\u003eNEXTITE AB200 will not adhere to plastics with a low surface energy such as Polypropylene (PP), Polyethylene (PE) or Polyolefins. These plastics can be structurally adhered to with NEXTITE AB206 and NEXTITE Cyanoacrylates also have a great bond when using NEXTITE SP 901 Primer.\u003c\/p\u003e\n\u003ch5\u003eSome applications of NEXTITE AB200 include:\u003c\/h5\u003e\n\u003cp\u003e \u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003eTransport Industry: Used to bond fibreglass (FRP), metal, and composites in vehicles like trucks, buses, trailers, and railcars.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003eMarine: Bonds composite hulls, decks, and marine components with strong resistance to moisture and saltwater.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003eConstruction: Joins panels, facades, and modular building elements where strength and quick curing are critical.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003eSignage and Displays: Bonds plastic, metal, and composite parts in signs and displays for indoor and outdoor use.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003eIndustrial Equipment: Used in machinery and appliance assembly for strong, impact- and vibration-resistant joints.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003eAutomotive: Bonding structural or cosmetic repair of body panels, including re-bonding fiberglass or composite components.\u003c\/p\u003e\n\u003ch5\u003eVersatility of NEXTITE AB200\u003c\/h5\u003e\n\u003cp\u003eWhile bond strength is important, it’s not the only factor to consider when selecting an adhesive. Once fully cured, NEXTITE AB200 delivers a range of additional benefits that can make a real difference depending on your application. \u003c\/p\u003e\n\u003cp\u003eWhen fully cured NEXTITE AB200 can be sanded, grinded, routed and polished to get your desired finish. You can even paint over it!\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003eGreat Chemical Resistance\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003eHigh resistance to weathering\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003eCan be used in indoor and outdoor applications\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003eWaterproofing when applied correctly\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003eHigh Temperature resistance -40 to 140°C\u003c\/p\u003e\n\u003ch3\u003eTools and Accessories\u003c\/h3\u003e\n\u003cp\u003eNEXTITE AB200 requires the use of a compatible dual cartridge dispensing applicator and static mixer nozzles, sold separately. Both the 50mL and 400mL Cartridges use standard 1:1 Ratio dual cartridge dispensing applicators and static mixers. It is important to use the correct applicator and mixer for each cartridge size, as 1:1 ratio systems are not compatible with other ratios cartridges and accessories. Each cartridge type requires the matching dispensing applicator and static mixer designed specifically for its ratio.\u003c\/p\u003e\n\u003ch5\u003e50mL Tubes\u003c\/h5\u003e\n\u003cp\u003eDispensing Applicator: Manual 50mL 1:1 Dispensing Applicator | Manual Hand Plunger for 1:1 50mL Cartridges (for one time use)\u003c\/p\u003e\n\u003cp\u003eStatic Mixer Nozzles: 1:1 50mL Quadro B Type (Standard Tip) | 1:1 50mL Quadro B Type (Narrow Tip)\u003c\/p\u003e\n\u003ch5\u003e400mL Tubes\u003c\/h5\u003e\n\u003cp\u003eDispensing Applicator: Manual 400mL 1:1 Dispensing Applicator | Pneumatic 400mL 1:1 Dispensing Applicator | Electric 400mL 1:1 Dispensing Applicator\u003c\/p\u003e\n\u003cp\u003eExtra Static Mixer Nozzles: 1:1 400mL Quadro F Type (Green – White Base)\u003c\/p\u003e\n\u003ch3\u003eTechnical Highlights\u003c\/h3\u003e\n\u003cdiv data-table=\"58844\" class=\"TablePress\"\u003e\u003cbr\u003e\u003c\/div\u003e\n\u003ch3\u003eStrength Tests\u003c\/h3\u003e\n\u003cdiv data-table=\"58842\" class=\"TablePress\"\u003e\u003cbr\u003e\u003c\/div\u003e\n\u003cp class=\"MsoNormal\" style=\"line-height: 150%;\"\u003e\u003cspan style=\"font-size: 10.0pt; line-height: 150%; font-family: 'Arial',sans-serif;\"\u003e** SF, AF, CF – determine how the substrate failed.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp class=\"MsoListParagraphCxSpFirst\" style=\"text-indent: -18.0pt; line-height: 150%; mso-list: l0 level1 lfo1;\"\u003e\u003c!-- [if !supportLists]--\u003e\u003cspan style=\"font-size: 10.0pt; line-height: 150%; font-family: 'Arial',sans-serif; mso-fareast-font-family: Arial;\"\u003e\u003cspan style=\"mso-list: Ignore;\"\u003e-\u003cspan style=\"font: 7.0pt 'Times New Roman';\"\u003e        \u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c!--[endif]--\u003e\u003cspan style=\"font-size: 10.0pt; line-height: 150%; font-family: 'Arial',sans-serif;\"\u003eSF – Substrate Failure\u003c\/span\u003e\u003c\/p\u003e\n\u003cp class=\"MsoListParagraphCxSpMiddle\" style=\"text-indent: -18.0pt; line-height: 150%; mso-list: l0 level1 lfo1;\"\u003e\u003c!-- [if !supportLists]--\u003e\u003cspan style=\"font-size: 10.0pt; line-height: 150%; font-family: 'Arial',sans-serif; mso-fareast-font-family: Arial;\"\u003e\u003cspan style=\"mso-list: Ignore;\"\u003e-\u003cspan style=\"font: 7.0pt 'Times New Roman';\"\u003e        \u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c!--[endif]--\u003e\u003cspan style=\"font-size: 10.0pt; line-height: 150%; font-family: 'Arial',sans-serif;\"\u003eAF – Adhesion Failure\u003c\/span\u003e\u003c\/p\u003e\n\u003cp class=\"MsoListParagraphCxSpLast\" style=\"text-indent: -18.0pt; line-height: 150%; mso-list: l0 level1 lfo1;\"\u003e\u003c!-- [if !supportLists]--\u003e\u003cspan style=\"font-size: 10.0pt; line-height: 150%; font-family: 'Arial',sans-serif; mso-fareast-font-family: Arial;\"\u003e\u003cspan style=\"mso-list: Ignore;\"\u003e-\u003cspan style=\"font: 7.0pt 'Times New Roman';\"\u003e        \u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c!--[endif]--\u003e\u003cspan style=\"font-size: 10.0pt; line-height: 150%; font-family: 'Arial',sans-serif;\"\u003eCF – Cohesive Failure\u003c\/span\u003e\u003c\/p\u003e\n\u003ch3\u003eChemical Resistance\u003c\/h3\u003e\n\u003cdiv data-table=\"58843\" class=\"TablePress\"\u003e\u003cbr\u003e\u003c\/div\u003e\n\u003ch3\u003eInstructions for use\u003c\/h3\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e1.     \u003c!--[endif]--\u003eUse a static mixer nozzle to accurately mix the contents of the 1:1 cartridge. Each cartridge includes one Static Mixer Nozzle Green 1:1, and you can purchase more in 5, 10 and 50 packs from our store.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e2.     \u003c!--[endif]--\u003eYou will also require a 1:1 Static Mixing Dispenser to push the contents through the static mixer. This is the best way to apply it and get accurate, dependable results every time.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e3.     \u003c!--[endif]--\u003eParts to be joined should fit without forcing and be clean, it is recommended to use NEXTITE PROPREP prior to applying any product to remove any oils, dust and dirt. It is important to let out any air bubbles and ensure adhesive is fully mixed by dispensing the first part of the cartridge onto some paper. This is to make sure the two separate parts are fully mixed and is generally the first 2-3mL. Apply adhesive directly from the static mixer.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e4.     \u003c!--[endif]--\u003ePress parts together in firm contact and use a clamp to secure while the glue reacts. NEXTITE AB200 will achieve a working strength within 14-17 min and full cure strength within 24 hours. You have approximately 4-6 minutes to work with the glue before it starts to set off.\u003c\/p\u003e\n\u003cp\u003ePlease check the TDS for material suitability and strength of each bond. For a tutorial how to use please refer to our YouTube Chanel.\u003c\/p\u003e\n\u003ch3\u003eShelf Life, Storage and Pack Size\u003c\/h3\u003e\n\u003cp\u003eNEXTITE AB200 has a 12 Month Shelf Life when stored correctly.\u003c\/p\u003e\n\u003cp\u003eStore in a cool dry place out of direct sunlight, an enclosed cabinet is recommended, to extend the shelf life of this product. Keep the open container tightly closed do not leave open. \u003c\/p\u003e\n\u003cp\u003e50mL and 400mL Cartridges as well as 20kg Pails and 200kg Drums for high volume use.\u003c\/p\u003e\n\u003ch3\u003eDownloads\u003c\/h3\u003e\n\u003cp\u003eNEXTITE AB200 Technical Data Sheet | NEXTITE AB200 Material Safety Data Sheet\u003c\/p\u003e","brand":"NEXTITE","offers":[{"title":"50mL","offer_id":46409535717525,"sku":"AB200-50","price":34.15,"currency_code":"AUD","in_stock":true},{"title":"400mL","offer_id":46409535750293,"sku":"AB200-400","price":116.8,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0740\/9834\/4085\/files\/NEXTITEAB20050mL_6c0c0250-0f06-400a-a44f-04780dc690fc.jpg?v=1770618979"},{"product_id":"nextite-ab206","title":"NEXTITE AB206 PP\/PE Adhesive","description":"\u003cp\u003eNEXTITE AB206 is a two-part MMA adhesive designed to structurally bond hard-to-glue plastics like polypropylene and polyethylene without primers or surface prep. It delivers strong, chemical-resistant bonds to polyolefin’s, metals, and composites, making it ideal for automotive, industrial, plastic assembly applications and is ideal for bonding dissimilar surfaces.\u003c\/p\u003e\n\u003ch3\u003eProduct Overview\u003c\/h3\u003e\n\u003cp\u003eNEXTITE AB206 is a structural two-part acrylic-based adhesive engineered specifically for bonding difficult, low surface energy plastics like polypropylene (PP), polyethylene (PE), PTFE, and PVDF. With a 10:1 mix ratio and a working time of 5 to 6 minutes, this adhesive delivers strong, structural bonds at room temperature without the need for primers or surface treatments, making it a faster, more efficient solution for challenging substrates.\u003c\/p\u003e\n\u003cp\u003eDeveloped as a polyolefin bonder, NEXTITE AB206 creates high-performance, permanent bonds where other adhesives struggle. Once cured, it offers excellent resistance to water, humidity, and chemicals. This makes it ideal for industrial, automotive, and assembly applications where long-term durability is essential. It also features a low exothermic reaction during bonding, which reduces the risk of material distortion.\u003c\/p\u003e\n\u003cp\u003eNEXTITE AB206 bonds both similar and dissimilar materials, including plastics, metals, and composites, even with minimal surface preparation. This can significantly reduce labour time and production costs while improving bond consistency and part aesthetics. It is also an ideal alternative to mechanical fasteners, rivets, solvent welding, or plastic welding.\u003c\/p\u003e\n\u003ch3\u003eApplications and Uses\u003c\/h3\u003e\n\u003cp\u003eNEXTITE AB206 bonds to a variety of substrates they include but aren’t limited to:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eLow Surface Energy Plastics: Polypropylene (PP) Polyethylene (PE – LDPE\/ HDPE), PTFE (Teflon), PVDF.\u003c\/li\u003e\n\u003cli\u003ePlastics: Acrylic (PMMA), Polycarbonate (PC), Acrylonitrile Butadiene Styrene (ABS), Polyvinyl Chloride (PVC)\u003c\/li\u003e\n\u003cli\u003eMetals: Aluminium, Steel, Stainless Steel, Powder Coated Surfaces\u003c\/li\u003e\n\u003cli\u003eComposites: Fibreglass Reinforced Plastic (FRP), Carbon Fibre (CF)\u003c\/li\u003e\n\u003cli\u003eOther: Glass, Concrete, Wood, MDF, Thermoplastic Elastomers (TPE)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eNEXTITE AB206 will not adhere to Nylons or Silicone surfaces.\u003c\/p\u003e\n\u003ch5\u003eSome applications of NEXTITE AB206 include\u003c\/h5\u003e\n\u003cul\u003e\n\u003cli\u003eEngineering Plastic Fabrication\u003c\/li\u003e\n\u003cli\u003eReplacing the need for hardware, rivets or welding in production\u003c\/li\u003e\n\u003cli\u003eMany cases where PP or PE need to be bonded to themselves or other materials\u003c\/li\u003e\n\u003cli\u003eRepairing PP\/PE Parts\u003c\/li\u003e\n\u003cli\u003eAutomotive Part Repair or Fixture\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch5\u003eVersatility of NEXTITE AB206\u003c\/h5\u003e\n\u003cp\u003eWhile bond strength is important, it’s not the only factor to consider when selecting an adhesive. Once fully cured, NEXTITE AB206 delivers a range of additional benefits that can make a real difference depending on your application.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eWhen fully cured NEXTITE AB206 can be sanded, grinded, routed and polished to get your desired finish.\u003c\/li\u003e\n\u003cli\u003eGreat Chemical Resistance – Ethylene Glycol, Brake Fluid, Power Steering Fluid, Iso-Pentane\u003c\/li\u003e\n\u003cli\u003eHigh resistance to weathering and humid environments\u003c\/li\u003e\n\u003cli\u003eCan be used in indoor and outdoor applications\u003c\/li\u003e\n\u003cli\u003eWaterproofing when applied correctly\u003c\/li\u003e\n\u003cli\u003eGood Temperature resistance -40 to 80°C\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eTools and Accessories\u003c\/h3\u003e\n\u003cp\u003eNEXTITE AB206 requires the use of a compatible dual cartridge dispensing applicator and static mixer nozzles, sold separately. The 50mL Cartridges use standard 10:1 Ratio dual cartridge dispensing applicators and static mixers. It is important to use the correct applicator and mixer for each cartridge size, as 10:1 ratio systems are not compatible with other ratios cartridges and accessories. Each cartridge type requires the matching dispensing applicator and static mixer designed specifically for its ratio.\u003c\/p\u003e\n\u003ch5\u003e50mL Tubes\u003c\/h5\u003e\n\u003cp\u003eDispensing Applicator: Manual 50mL 10:1 Dispensing Applicator | Manual Hand Plunger for 10:1 50mL Cartridges (for one time use)\u003c\/p\u003e\n\u003cp\u003eStatic Mixer Nozzles: 10:1 50mL Quadro B Type (Standard Tip) | 10:1 50mL Quadro B Type (Narrow Tip)\u003c\/p\u003e\n\u003ch3\u003eTechnical Highlights\u003c\/h3\u003e\n\u003cdiv class=\"TablePress\" data-table=\"58845\"\u003e\u003cbr\u003e\u003c\/div\u003e\n\u003ch3\u003eStrength Tests\u003c\/h3\u003e\n\u003cdiv class=\"TablePress\" data-table=\"58846\"\u003e\u003cbr\u003e\u003c\/div\u003e\n\u003cp style=\"line-height: 150%;\" class=\"MsoNormal\"\u003e\u003cspan style=\"font-size: 10.0pt; line-height: 150%; font-family: 'Arial',sans-serif;\"\u003e** SF, AF, CF – determine how the substrate failed.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp style=\"text-indent: -18.0pt; line-height: 150%; mso-list: l0 level1 lfo1;\" class=\"MsoListParagraphCxSpFirst\"\u003e\u003c!-- [if !supportLists]--\u003e\u003cspan style=\"font-size: 10.0pt; line-height: 150%; font-family: 'Arial',sans-serif; mso-fareast-font-family: Arial;\"\u003e\u003cspan style=\"mso-list: Ignore;\"\u003e-\u003cspan style=\"font: 7.0pt 'Times New Roman';\"\u003e        \u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c!--[endif]--\u003e\u003cspan style=\"font-size: 10.0pt; line-height: 150%; font-family: 'Arial',sans-serif;\"\u003eSF – Substrate Failure\u003c\/span\u003e\u003c\/p\u003e\n\u003cp style=\"text-indent: -18.0pt; line-height: 150%; mso-list: l0 level1 lfo1;\" class=\"MsoListParagraphCxSpMiddle\"\u003e\u003c!-- [if !supportLists]--\u003e\u003cspan style=\"font-size: 10.0pt; line-height: 150%; font-family: 'Arial',sans-serif; mso-fareast-font-family: Arial;\"\u003e\u003cspan style=\"mso-list: Ignore;\"\u003e-\u003cspan style=\"font: 7.0pt 'Times New Roman';\"\u003e        \u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c!--[endif]--\u003e\u003cspan style=\"font-size: 10.0pt; line-height: 150%; font-family: 'Arial',sans-serif;\"\u003eAF – Adhesion Failure\u003c\/span\u003e\u003c\/p\u003e\n\u003cp style=\"text-indent: -18.0pt; line-height: 150%; mso-list: l0 level1 lfo1;\" class=\"MsoListParagraphCxSpLast\"\u003e\u003c!-- [if !supportLists]--\u003e\u003cspan style=\"font-size: 10.0pt; line-height: 150%; font-family: 'Arial',sans-serif; mso-fareast-font-family: Arial;\"\u003e\u003cspan style=\"mso-list: Ignore;\"\u003e-\u003cspan style=\"font: 7.0pt 'Times New Roman';\"\u003e        \u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c!--[endif]--\u003e\u003cspan style=\"font-size: 10.0pt; line-height: 150%; font-family: 'Arial',sans-serif;\"\u003eCF – Cohesive Failure\u003c\/span\u003e\u003c\/p\u003e\n\u003ch3\u003eInstructions for use\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eUse a static mixer nozzle to accurately mix the contents of the 10:1 cartridge. Each cartridge includes one Static Mixer Nozzle Orange 10:1, and you can purchase more in 5, 10 and 50 packs from our store.\u003c\/li\u003e\n\u003cli\u003eYou will also require a 10:1 Static Mixing Dispenser to push the contents through the static mixer. This is the best way to apply it and get accurate, dependable results every time.\u003c\/li\u003e\n\u003cli\u003eParts to be joined should fit without forcing and be clean, it is recommended to use NEXTITE PROPREP prior to applying any product to remove any oils, dust and dirt. It is important to let out any air bubbles and ensure adhesive is fully mixed by dispensing the first part of the cartridge onto some paper. This is to make sure the two separate parts are fully mixed and is generally the first 2-3mL. Apply adhesive directly from the static mixer.\u003c\/li\u003e\n\u003cli\u003ePress parts together in firm contact and use a clamp to secure while the glue reacts. NEXTITE AB206 will achieve a working strength within 90-240 min and full cure strength within 24 hours. You have approximately 5-6 minutes to work with the glue before it starts to set off.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003ePlease check the TDS for material suitability and strength of each bond. For a tutorial how to use please refer to our YouTube Chanel.\u003c\/p\u003e\n\u003ch3\u003eShelf Life, Storage and Pack Size\u003c\/h3\u003e\n\u003cp\u003eNEXTITE AB206 has a 9 Month Shelf Life when stored correctly.\u003c\/p\u003e\n\u003cp\u003eStore in a cool dry place out of direct sunlight, an enclosed cabinet is recommended, to extend the shelf life of this product. Keep the open container tightly closed do not leave open. \u003c\/p\u003e\n\u003cp\u003eNEXTITE AB206 is available in 50mL and 250mL Pack Sizes.\u003c\/p\u003e\n\u003ch3\u003eDownloads\u003c\/h3\u003e\n\u003cp\u003eNEXTITE AB206 Technical Data Sheet | NEXTITE AB206 Material Safety Data Sheet\u003c\/p\u003e","brand":"NEXTITE","offers":[{"title":"50mL","offer_id":47443848429717,"sku":"AB206-50","price":65.45,"currency_code":"AUD","in_stock":true},{"title":"250mL","offer_id":47443848462485,"sku":"AB206-250","price":270.6,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0740\/9834\/4085\/files\/NEXTITEAB20650mL_005ff05b-ce1d-4195-a4f6-3d08158b5827.jpg?v=1770618298"},{"product_id":"nextite-501","title":"NEXTITE 501 Surface Insensitive, Porous Materials","description":"\u003cp\u003eNEXTITE 501 is a high performance surface insensitive instant adhesive meaning it delivers high strength, reliable bonds across a wide range of materials making it an ideal general purpose solution. With its medium viscosity and fast cure speed, it sets in seconds on most substrates, providing virtually instant bonding on a wide range of materials including plastics, metals and rubbers. The surface insensitive formulation ensures consistent results even on rough, porous and acidic surfaces. While its high temperature resistance of up to 120°C makes it suitable for demanding applications.\u003c\/p\u003e\n\u003ch3\u003eProduct Overview\u003c\/h3\u003e\n\u003cp\u003eNEXTITE 501 is a surface insensitive instant adhesive which provides dependable bonding even on difficult substrates. It’s all around general purpose formulation makes it ideal for a wide range of applications including bonding plastics, metals and rubbers. Its surface insensitive formulation allows for bonding on rough, porous and acidic surfaces where other instant adhesives fall short. In addition to this, NEXTITE 501 offers excellent heat resistance, maintaining strong adhesion at temperatures up to 120°C. Perfect for both high strength bonding applications and any fast at home jobs or repairs.\u003c\/p\u003e\n\u003cp\u003eNEXTITE 501 has a medium viscosity 90 – 110 CPS at 25°C which provides excellent control during application and ensures precise placement of adhesive. Unlike lower viscosity instant adhesives, it does not immediately run or spread out once applied, allowing the user more working control and reducing mess. NEXTITE 501 cures rapidly, achieving strong bonds on most substrates in approximately 15 seconds. It allows for 0.15 mm of gap filling and is very high strength on close fitting parts.\u003c\/p\u003e\n\u003ch5\u003eNEXTITE SP 901 Polyolefin Primer\u003c\/h5\u003e\n\u003cp\u003eNEXTITE SP 901 is a surface primer for making polyolefins and other low surface energy surfaces suitable for bonding with NEXTITE Instant Adhesives. It is suitable to prime the notoriously difficult to bond surfaces such as polyethylene, polypropylene and polytetrafluoroethylene (PTFE). NEXTITE SP 901 works well with all of our cyanoacrylate adhesives especially the faster fixture time ones.\u003c\/p\u003e\n\u003ch5\u003e NEXTITE CA-1 Cyanoacrylate Activator\u003c\/h5\u003e\n\u003cp\u003eNEXTITE CA-1 can be used in conjunction with NEXTITE Cyanoacrylate Adhesives to promote a faster cure and to extend their gap-filling capabilities. Cyanoacrylate Adhesives naturally have limited gap-filling ability, but the use of an activator helps extend this capability by curing the adhesive almost instantly. Using a cyanoacrylate activator it also enables fillets of cured adhesive to be formed if required and can be used to reduce the effects of blooming, which can affect decorative surfaces. CA-1 is particularly effective when bonding porous materials, as the rapid curing prevents the adhesive from soaking in and ensures a stronger more reliable bond. \u003c\/p\u003e\n\u003ch3\u003eApplications and Uses\u003c\/h3\u003e\n\u003cp\u003eNEXTITE 501 has been designed as a surface insensitive instant adhesive. It is ideal for industries and tasks that require a general purpose adhesive with instant bond and high strength. It is also ideal for surfaces that have a rough, porous or acidic surface making this adhesive a true allrounder.\u003c\/p\u003e\n\u003ch3\u003eTools and Accessories\u003c\/h3\u003e\n\u003cp\u003eThe 20g and 50g bottles are specifically designed to work with a variety of nozzles and tips, so users can adapt the application method without the need to transfer the adhesive into another container. The nozzles come in a variety of internal diameters and lengths for all types of applications. They easily press-fit directly onto the tip of the instant adhesive bottle. The benefit of using alternative tips is that it gives users greater control, allowing only a precise amount of adhesive to be dispensed. They also extend the reach of the bottle, making it easier to apply adhesive accurately in tight spaces or detailed applications. \u003c\/p\u003e\n\u003cp\u003eFor NEXTITE 501, we recommend either the 0.6mm or 0.8mm tips or nozzles.\u003c\/p\u003e\n\u003ch3\u003eTechnical Highlights\u003c\/h3\u003e\n\u003cdiv data-table=\"58788\" class=\"TablePress\"\u003e\u003cbr\u003e\u003c\/div\u003e\n\u003ch3\u003eInstructions for use\u003c\/h3\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e1.     \u003c!--[endif]--\u003eEnsure all bonding surfaces are clean and free of grease. Use NEXTITE PROPREP or ACRI-BOND CLEANER (for delicate materials) and allow the surfaces to dry completely.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e2.     \u003c!--[endif]--\u003eFor low surface energy plastics, apply NEXTITE SP 901 Primer to the bonding area. Use sparingly and avoid excess application. Let the primer dry fully. Do not use primer on plastics that are not low surface energy.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e3.     \u003c!--[endif]--\u003eIf required, NEXTITE CA-1 Activator can be applied. Apply to one bonding surface only. If a primer has been used, do not apply activator to the same area. Allow the activator to dry before proceeding.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e4.     \u003c!--[endif]--\u003eDispense adhesive onto one surface only (never on the surface treated with activator). Assemble the components quickly, as the rapid fixture time provides little chance for repositioning.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e5.     \u003c!--[endif]--\u003eTo cure excess adhesive or fillets outside the bond line, apply NEXTITE CA-1 Activator by spraying or dropping directly onto the exposed adhesive.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e6.     \u003c!--[endif]--\u003eKeep the parts fixed or clamped in position until the adhesive has achieved fixture.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e7.     \u003c!--[endif]--\u003eAllow the bond to reach full strength before applying service loads, which typically occurs after 24 to 72 hours depending on the bond line, substrates and environmental conditions.\u003c\/p\u003e\n\u003ch3\u003eShelf Life, Storage and Pack Size\u003c\/h3\u003e\n\u003cp\u003eNEXTITE 501 has an 18 Month Shelf Life when stored correctly.\u003c\/p\u003e\n\u003cp\u003eStore in a cool dry place out of direct sunlight, an enclosed cabinet is recommended, to extend the shelf life of this product. Keep the open container tightly closed do not leave open.\u003c\/p\u003e\n\u003cp\u003eOur Specialised Instant Adhesives come in three size options 20g, 50g and 500g.\u003c\/p\u003e\n\u003ch3\u003eDownloads\u003c\/h3\u003e\n\u003cp style=\"line-height: 150%;\" class=\"MsoNormal\"\u003eNEXTITE 501 Technical Data Sheet | NEXTITE 501 Material Safety Data Sheet\u003c\/p\u003e","brand":"NEXTITE","offers":[{"title":"20g","offer_id":46469490016405,"sku":"50120","price":16.7,"currency_code":"AUD","in_stock":true},{"title":"50g","offer_id":46469490049173,"sku":"50150","price":31.9,"currency_code":"AUD","in_stock":true},{"title":"500g","offer_id":46469490081941,"sku":"501500","price":159.5,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0740\/9834\/4085\/files\/NEXTITE_501_20g.jpg?v=1771381060"},{"product_id":"nextite-503","title":"NEXTITE 503 Low Odour\/ Low Bloom Thick Viscosity","description":"\u003cp\u003eNEXTITE 503 is a high performance, low odour, low bloom instant adhesive designed for applications where high visual appearance matters. NEXTITE 503 is a medium to high viscosity adhesive allowing for more control and an extended fixture time. It minimises frosting, making it ideal for bonds that require a clean, high-quality finish. The fast cure speed delivers virtually instant bonding on a wide range of materials including plastics, metals and rubbers. With its medium to thick viscosity, NEXTITE 503 allows for controlled, precise application. Its low odour formulation also improves workplace comfort and reduces the need for ventilation.\u003c\/p\u003e\n\u003ch3\u003eProduct Overview\u003c\/h3\u003e\n\u003cp\u003eNEXTITE 503 is a modified cyanoacrylate adhesive designed to be low odour and low bloom for high visual and cosmetic applications. Blooming is the white frosting that appears when using conventional cyanoacrylate adhesives. In many cases this isn’t an issue, but when working with decorative components, painted surfaces or highly sensitive materials where appearance is critical, blooming can compromise the finish and reduce the overall quality appearance of the final product. At the same time, its low odour formulation improves comfort and safety in the workplace, making it suitable for all types of work environments including enclosed and poorly ventilated areas. By minimising bloom and odour NEXTITE 503 ensures clean, professional bonds that maintain structural and aesthetic integrity of the assembly without compromising user comfort.\u003c\/p\u003e\n\u003cp\u003eNEXTITE 503 has a medium to high viscosity of 1100 – 1700 CPS at 25°C, which provides excellent control during application and ensures precise placement of adhesive. Unlike lower viscosity instant adhesives, it does not immediately run or spread out once applied, allowing the user more working control and reducing mess. In addition, due to the thickened formula it offers gap filling of up to 0.20 mm. It also allows an extended fixture time allowing users more time to precisely align parts before fixturing. NEXTITE 503 is highly versatile, bonding quickly and securely to a wide range of materials. It is especially effective on most plastics, metals and rubbers.\u003c\/p\u003e\n\u003ch5\u003eNEXTITE SP 901 Polyolefin Primer\u003c\/h5\u003e\n\u003cp\u003eNEXTITE SP 901 is a surface primer for making polyolefins and other low surface energy surfaces suitable for bonding with NEXTITE Instant Adhesives. It is suitable to prime the notoriously difficult to bond surfaces such as polyethylene, polypropylene and polytetrafluoroethylene (PTFE). NEXTITE SP 901 works well with all of our cyanoacrylate adhesives especially the faster fixture time ones.\u003c\/p\u003e\n\u003ch5\u003eNEXTITE CA-1 Cyanoacrylate Activator\u003c\/h5\u003e\n\u003cp\u003eNEXTITE CA-1 can be used in conjunction with NEXTITE Cyanoacrylate Adhesives to promote a faster cure and to extend their gap-filling capabilities. Cyanoacrylate Adhesives naturally have limited gap-filling ability, but the use of an activator helps extend this capability by curing the adhesive almost instantly. Using a cyanoacrylate activator it also enables fillets of cured adhesive to be formed if required and can be used to reduce the effects of blooming, which can affect decorative surfaces. CA-1 is particularly effective when bonding porous materials, as the rapid curing prevents the adhesive from soaking in and ensures a stronger more reliable bond. \u003c\/p\u003e\n\u003ch3\u003eApplications and Uses\u003c\/h3\u003e\n\u003cp\u003eNEXTITE 503 has been designed as a low bloom and low odour instant adhesive. It is ideal for industries and tasks that require an instant bond, high strength and an aesthetic finish. It is also ideal for workspaces that have little to no ventilation as it does not compromise user comfort.\u003c\/p\u003e\n\u003ch3\u003eTools and Accessories\u003c\/h3\u003e\n\u003cp\u003eThe 20g and 50g bottles are specifically designed to work with a variety of nozzles and tips, so users can adapt the application method without the need to transfer the adhesive into another container. The nozzles come in a variety of internal diameters and lengths for all types of applications. They easily press-fit directly onto the tip of the instant adhesive bottle. The benefit of using alternative tips is that it gives users greater control, allowing only a precise amount of adhesive to be dispensed. They also extend the reach of the bottle, making it easier to apply adhesive accurately in tight spaces or detailed applications.\u003c\/p\u003e\n\u003cp\u003eFor NEXTITE 503, we recommend either the 0.8mm (Green) or 1.4mm (Dark Green) tips or nozzles.\u003c\/p\u003e\n\u003ch3\u003eTechnical Highlights\u003c\/h3\u003e\n\u003cdiv class=\"TablePress\" data-table=\"58765\"\u003e\u003cbr\u003e\u003c\/div\u003e\n\u003ch3\u003eInstructions for use\u003c\/h3\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e1.     \u003c!--[endif]--\u003eEnsure all bonding surfaces are clean and free of grease. Use NEXTITE PROPREP or ACRI-BOND CLEANER (for delicate materials) and allow the surfaces to dry completely.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e2.     \u003c!--[endif]--\u003eFor low surface energy plastics, apply NEXTITE SP 901 Primer to the bonding area. Use sparingly and avoid excess application. Let the primer dry fully. Do not use primer on plastics that are not low surface energy.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e3.     \u003c!--[endif]--\u003eIf required, NEXTITE CA-1 Activator can be applied. Apply to one bonding surface only. If a primer has been used, do not apply activator to the same area. Allow the activator to dry before proceeding.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e4.     \u003c!--[endif]--\u003eDispense adhesive onto one surface only (never on the surface treated with activator). Assemble the components quickly, as the rapid fixture time provides little chance for repositioning.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e5.     \u003c!--[endif]--\u003eTo cure excess adhesive or fillets outside the bond line, apply NEXTITE CA-1 Activator by spraying or dropping directly onto the exposed adhesive.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e6.     \u003c!--[endif]--\u003eKeep the parts fixed or clamped in position until the adhesive has achieved fixture.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e7.     \u003c!--[endif]--\u003eAllow the bond to reach full strength before applying service loads, which typically occurs after 24 to 72 hours depending on the bond line, substrates and environmental conditions. \u003c\/p\u003e\n\u003ch3\u003eShelf Life, Storage and Pack Size\u003c\/h3\u003e\n\u003cp\u003eNEXTITE 503 has an 18 Month Shelf Life when stored correctly.\u003c\/p\u003e\n\u003cp\u003eStore in a cool dry place out of direct sunlight, an enclosed cabinet is recommended, to extend the shelf life of this product. Keep the open container tightly closed do not leave open.\u003c\/p\u003e\n\u003cp\u003eOur Specialised Instant Adhesives come in three size options 20g, 50g and 500g.\u003c\/p\u003e\n\u003ch3\u003eDownloads\u003c\/h3\u003e\n\u003cp\u003eNEXTITE 503 Technical Data Sheet | NEXTITE 503 Material Safety Data Sheet\u003c\/p\u003e","brand":"NEXTITE","offers":[{"title":"20g","offer_id":46462431133845,"sku":"50320","price":26.2,"currency_code":"AUD","in_stock":true},{"title":"50g","offer_id":46462431166613,"sku":"50350","price":51.2,"currency_code":"AUD","in_stock":true},{"title":"500g","offer_id":46462431199381,"sku":"503500","price":257.5,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0740\/9834\/4085\/files\/NEXTITE_503_20g.jpg?v=1771381060"},{"product_id":"nextite-554","title":"NEXTITE 554 Non Drip Gel, Surface Insensitive 20g","description":"\u003cp\u003eNEXTITE 554 is a high performance surface insensitive instant adhesive in a non-drip gel form, perfect for applications that require control or vertical bonding. It delivers high strength, reliable bonds across a wide range of materials making it an ideal general purpose solution. With its thick gel viscosity and fast cure speed, it sets in seconds on most substrates, providing virtually instant bonding on a wide range of materials including plastics, metals and rubbers. The surface insensitive formulation ensures consistent results even on rough, porous and acidic surfaces.\u003c\/p\u003e\n\u003ch3\u003eProduct Overview\u003c\/h3\u003e\n\u003cp\u003eNEXTITE 554 is a surface insensitive, non-drip gel instant adhesive which provides dependable bonding even on difficult substrates. It’s designed for the assembly of difficult-to-bond materials which require uniform stress distribution. NEXTITE 554’s all around general purpose formulation makes it ideal for a wide range of applications including bonding plastics, metals and rubbers as well as porous materials such as wood, paper, leather and fabric. Its surface insensitive formulation allows for bonding on rough, porous and acidic surfaces where other instant adhesives fall short. Perfect for both high strength bonding applications and any fast at home jobs or repairs.\u003c\/p\u003e\n\u003cp\u003eNEXTITE 554 is a high viscosity gel which provides excellent control during application and ensures precise placement of adhesive. It’s perfect for vertical bonding applications where a non-drip and non-run feature is necessary. Unlike lower viscosity instant adhesives, it does not run or spread out once applied, allowing the user more working control and reducing mess. NEXTITE 554 cures rapidly, achieving strong bonds on most substrates in approximately 15 seconds. It allows for 0.15 mm of gap filling and is very high strength on close fitting parts.\u003c\/p\u003e\n\u003ch5\u003eNEXTITE SP 901 Polyolefin Primer\u003c\/h5\u003e\n\u003cp\u003eNEXTITE SP 901 is a surface primer for making polyolefins and other low surface energy surfaces suitable for bonding with NEXTITE Instant Adhesives. It is suitable to prime the notoriously difficult to bond surfaces such as polyethylene, polypropylene and polytetrafluoroethylene (PTFE). NEXTITE SP 901 works well with all of our cyanoacrylate adhesives especially the faster fixture time ones.\u003c\/p\u003e\n\u003ch5\u003eNEXTITE CA-1 Cyanoacrylate Activator\u003c\/h5\u003e\n\u003cp\u003eNEXTITE CA-1 can be used in conjunction with NEXTITE Cyanoacrylate Adhesives to promote a faster cure and to extend their gap-filling capabilities. Cyanoacrylate Adhesives naturally have limited gap-filling ability, but the use of an activator helps extend this capability by curing the adhesive almost instantly. Using a cyanoacrylate activator it also enables fillets of cured adhesive to be formed if required and can be used to reduce the effects of blooming, which can affect decorative surfaces. CA-1 is particularly effective when bonding porous materials, as the rapid curing prevents the adhesive from soaking in and ensures a stronger more reliable bond.\u003c\/p\u003e\n\u003ch3\u003eApplications and Uses\u003c\/h3\u003e\n\u003cp\u003eNEXTITE 554 has been designed as a surface insensitive, non-drip gel instant adhesive. It is ideal for industries and tasks that require a general purpose adhesive with instant bond and high strength. It is also ideal for surfaces that have a rough, porous or acidic surface making this adhesive a true allrounder. \u003c\/p\u003e\n\u003ch3\u003eTools and Accessories\u003c\/h3\u003e\n\u003cp\u003eNEXTITE 554 is designed to be used directly out of the tube.\u003c\/p\u003e\n\u003ch3\u003eTechnical Highlights\u003c\/h3\u003e\n\u003cdiv class=\"TablePress\" data-table=\"58802\"\u003e\u003c\/div\u003e\n\u003ch3\u003eInstructions for use\u003c\/h3\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e1.     \u003c!--[endif]--\u003eEnsure all bonding surfaces are clean and free of grease. Use NEXTITE PROPREP or ACRI-BOND CLEANER (for delicate materials) and allow the surfaces to dry completely.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e2.     \u003c!--[endif]--\u003eFor low surface energy plastics, apply NEXTITE SP 901 Primer to the bonding area. Use sparingly and avoid excess application. Let the primer dry fully. Do not use primer on plastics that are not low surface energy.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e3.     \u003c!--[endif]--\u003eIf required, NEXTITE CA-1 Activator can be applied. Apply to one bonding surface only. If a primer has been used, do not apply activator to the same area. Allow the activator to dry before proceeding.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e4.     \u003c!--[endif]--\u003eDispense adhesive onto one surface only (never on the surface treated with activator). Assemble the components quickly, as the rapid fixture time provides little chance for repositioning.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e5.     \u003c!--[endif]--\u003eTo cure excess adhesive or fillets outside the bond line, apply NEXTITE CA-1 Activator by spraying or dropping directly onto the exposed adhesive.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e6.     \u003c!--[endif]--\u003eKeep the parts fixed or clamped in position until the adhesive has achieved fixture.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e7.     \u003c!--[endif]--\u003eAllow the bond to reach full strength before applying service loads, which typically occurs after 24 to 72 hours depending on the bond line, substrates and environmental conditions.\u003c\/p\u003e\n\u003ch3\u003eShelf Life and Storage\u003c\/h3\u003e\n\u003cp\u003eNEXTITE 554 has an 18 Month Shelf Life when stored correctly.\u003c\/p\u003e\n\u003cp\u003eStore in a cool dry place out of direct sunlight, an enclosed cabinet is recommended, to extend the shelf life of this product. Keep the open container tightly closed do not leave open. \u003c\/p\u003e\n\u003ch3\u003eDownloads\u003c\/h3\u003e\n\u003cp\u003eNEXTITE 554 Technical Data Sheet | NEXTITE 554 Material Safety Data Sheet\u003c\/p\u003e","brand":"NEXTITE","offers":[{"title":"Default Title","offer_id":46411843797141,"sku":"55420","price":24.8,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0740\/9834\/4085\/files\/NEXTITE_554_20g.jpg?v=1771381060"},{"product_id":"nextite-560","title":"NEXTITE 560 Low Odour\/ Low Bloom Thin Viscosity","description":"\u003cp\u003eNEXTITE 560 is a high performance, low odour, low bloom instant adhesive designed for applications where high visual appearance matters. NEXTITE 560 is low viscosity and an ultra-fast set on most materials. It minimises frosting, making it ideal for bonds that require a clean, high-quality finish. The fast cure speed delivers virtually instant bonding on a wide range of materials including plastics, metals and rubbers. Its low odour formulation also improves workplace comfort and reduces the need for ventilation.\u003c\/p\u003e\n\u003ch3\u003eProduct Overview\u003c\/h3\u003e\n\u003cp\u003eNEXTITE 560 is a modified cyanoacrylate adhesive designed to be low odour and low bloom for high visual and cosmetic applications. Blooming is the white frosting that appears when using conventional cyanoacrylate adhesives. In many cases this isn’t an issue, but when working with decorative components, painted surfaces or highly sensitive materials where appearance is critical, blooming can compromise the finish and reduce the overall quality appearance of the final product. At the same time, its low odour formulation improves comfort and safety in the workplace, making it suitable for all types of work environments including enclosed and poorly ventilated areas. By minimising bloom and odour NEXTITE 560 ensures clean, professional bonds that maintain structural and aesthetic integrity of the assembly without compromising user comfort.\u003c\/p\u003e\n\u003cp\u003eNEXTITE 560 has a low viscosity of 30 – 50 CPS at 25°C, which provides an ultra-fast set on most materials and allows for wicking into tight fitting parts. It allows for 0.10 mm of gap filling, so it is best suited for parts with good tolerances. NEXTITE 560 is highly versatile, bonding quickly and securely to a wide range of materials. It is especially effective on most plastics, metals and rubbers.\u003c\/p\u003e\n\u003ch5\u003eNEXTITE SP 901 Polyolefin Primer\u003c\/h5\u003e\n\u003cp\u003eNEXTITE SP 901 is a surface primer for making polyolefins and other low surface energy surfaces suitable for bonding with NEXTITE Instant Adhesives. It is suitable to prime the notoriously difficult to bond surfaces such as polyethylene, polypropylene and polytetrafluoroethylene (PTFE). NEXTITE SP 901 works well with all of our cyanoacrylate adhesives especially the faster fixture time ones.\u003c\/p\u003e\n\u003ch5\u003eNEXTITE CA-1 Cyanoacrylate Activator\u003c\/h5\u003e\n\u003cp\u003eNEXTITE CA-1 can be used in conjunction with NEXTITE Cyanoacrylate Adhesives to promote a faster cure and to extend their gap-filling capabilities. Cyanoacrylate Adhesives naturally have limited gap-filling ability, but the use of an activator helps extend this capability by curing the adhesive almost instantly. Using a cyanoacrylate activator it also enables fillets of cured adhesive to be formed if required and can be used to reduce the effects of blooming, which can affect decorative surfaces. CA-1 is particularly effective when bonding porous materials, as the rapid curing prevents the adhesive from soaking in and ensures a stronger more reliable bond.\u003c\/p\u003e\n\u003ch3\u003eApplications and Uses\u003c\/h3\u003e\n\u003cp\u003eNEXTITE 560 has been designed as a low bloom and low odour instant adhesive. It is ideal for industries and tasks that require an instant bond, high strength and an aesthetic finish. It is also ideal for workspaces that have little to no ventilation as it does not compromise user comfort.\u003c\/p\u003e\n\u003ch3\u003eTools and Accessories\u003c\/h3\u003e\n\u003cp\u003eThe 20g and 50g bottles are specifically designed to work with a variety of nozzles and tips, so users can adapt the application method without the need to transfer the adhesive into another container. The nozzles come in a variety of internal diameters and lengths for all types of applications. They easily press-fit directly onto the tip of the instant adhesive bottle. The benefit of using alternative tips is that it gives users greater control, allowing only a precise amount of adhesive to be dispensed. They also extend the reach of the bottle, making it easier to apply adhesive accurately in tight spaces or detailed applications. \u003c\/p\u003e\n\u003cp\u003eFor NEXTITE 503, we recommend either the 0.5mm or 0.6mm tips or nozzles.\u003c\/p\u003e\n\u003ch3\u003eTechnical Highlights\u003c\/h3\u003e\n\u003cdiv class=\"TablePress\" data-table=\"58778\"\u003e\u003cbr\u003e\u003c\/div\u003e\n\u003ch3\u003eInstructions for use\u003c\/h3\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e1.     \u003c!--[endif]--\u003eEnsure all bonding surfaces are clean and free of grease. Use NEXTITE PROPREP or ACRI-BOND CLEANER (for delicate materials) and allow the surfaces to dry completely.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e2.     \u003c!--[endif]--\u003eFor low surface energy plastics, apply NEXTITE SP 901 Primer to the bonding area. Use sparingly and avoid excess application. Let the primer dry fully. Do not use primer on plastics that are not low surface energy.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e3.     \u003c!--[endif]--\u003eIf required, NEXTITE CA-1 Activator can be applied. Apply to one bonding surface only. If a primer has been used, do not apply activator to the same area. Allow the activator to dry before proceeding.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e4.     \u003c!--[endif]--\u003eDispense adhesive onto one surface only (never on the surface treated with activator). Assemble the components quickly, as the rapid fixture time provides little chance for repositioning.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e5.     \u003c!--[endif]--\u003eTo cure excess adhesive or fillets outside the bond line, apply NEXTITE CA-1 Activator by spraying or dropping directly onto the exposed adhesive.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e6.     \u003c!--[endif]--\u003eKeep the parts fixed or clamped in position until the adhesive has achieved fixture.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e7.     \u003c!--[endif]--\u003eAllow the bond to reach full strength before applying service loads, which typically occurs after 24 to 72 hours depending on the bond line, substrates and environmental conditions.\u003c\/p\u003e\n\u003ch3\u003eShelf Life, Storage and Pack Size\u003c\/h3\u003e\n\u003cp\u003eNEXTITE 560 has an 18 Month Shelf Life when stored correctly.\u003c\/p\u003e\n\u003cp\u003eStore in a cool dry place out of direct sunlight, an enclosed cabinet is recommended, to extend the shelf life of this product. Keep the open container tightly closed do not leave open.\u003c\/p\u003e\n\u003cp\u003eOur Specialised Instant Adhesives come in three size options 20g, 50g and 500g.\u003c\/p\u003e\n\u003ch3\u003eDownloads\u003cu\u003e\u003cspan style=\"font-size: 11.0pt; line-height: 150%; font-family: 'Arial',sans-serif;\"\u003e\u003c\/span\u003e\u003c\/u\u003e\n\u003c\/h3\u003e\n\u003cp\u003e\u003cmeta charset=\"utf-8\"\u003eNEXTITE 560 Technical Data Sheet | NEXTITE 560 Material Safety Data Sheet\u003c\/p\u003e","brand":"NEXTITE","offers":[{"title":"20g","offer_id":46465771012245,"sku":"56020","price":26.2,"currency_code":"AUD","in_stock":true},{"title":"50g","offer_id":46465771045013,"sku":"56050","price":51.2,"currency_code":"AUD","in_stock":true},{"title":"500g","offer_id":46465771077781,"sku":"560500","price":257.5,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0740\/9834\/4085\/files\/NEXTITE_560_20g.jpg?v=1771381060"},{"product_id":"nextite-580","title":"NEXTITE 580 Impact Resistant, Medium Black Rubber Toughened","description":"\u003cp\u003eNEXTITE 580 is a high performance black rubber toughened instant adhesive designed for superior durability and reliability. Its advanced rubber toughened formulation provides exceptional impact, peel and sheer strength, creating resilient bonds that can withstand demanding conditions and vibrations. The medium viscosity ensures controlled application whilst the slower cure time of 60 – 120 seconds gives users some extra time to position and align components before fixturing. NEXTITE 580 delivers excellent adhesion to a wide variety of materials including plastics, metals and rubbers.\u003c\/p\u003e\n\u003ch3\u003eProduct Overview\u003c\/h3\u003e\n\u003cp\u003eNEXTITE 580 is a rubber toughened instant adhesive designed for applications that require superior durability and flexibility. Its rubber toughened formulation provides exceptional impact resistance and greatly improves the peel and shear strength, ensuring reliable performance even under stress or vibration. The adhesive maintains good elasticity, allowing bonded joints to flex and move without failure, which is especially important when bonding dissimilar materials that expand or contract at different rates. This combination of strength and flexibility makes NEXTITE 580 ideal for assemblies subject to dynamic loads, temperature changes or movement in service.\u003c\/p\u003e\n\u003cp\u003eWith a medium viscosity of 100 – 150 CPS at 25°C, NEXTITE 580 offers excellent control during application, reducing mess and ensuring accurate adhesive placement. Its longer fixture time of 60 – 120 seconds depending on material, gives users the ability to position and align parts before the bond sets. This formulation provides gap filling of up to 0.20 mm and can withstand temperatures of up to 100°C (for higher temperature resistance consider NEXTITE 5210 for up to 120°C temperatures). It is ideal for a wide range of applications including bonding plastics, metals and rubbers. NEXTITE 580 is very high strength on close fitting parts.\u003c\/p\u003e\n\u003ch5\u003eNEXTITE SP 901 Polyolefin Primer\u003c\/h5\u003e\n\u003cp\u003eNEXTITE SP 901 is a surface primer for making polyolefins and other low surface energy surfaces suitable for bonding with NEXTITE Instant Adhesives. It is suitable to prime the notoriously difficult to bond surfaces such as polyethylene, polypropylene and polytetrafluoroethylene (PTFE). NEXTITE SP 901 works well with all of our cyanoacrylate adhesives especially the faster fixture time ones.\u003c\/p\u003e\n\u003ch5\u003eNEXTITE CA-1 Cyanoacrylate Activator\u003c\/h5\u003e\n\u003cp\u003eNEXTITE CA-1 can be used in conjunction with NEXTITE Cyanoacrylate Adhesives to promote a faster cure and to extend their gap-filling capabilities. Cyanoacrylate Adhesives naturally have limited gap-filling ability, but the use of an activator helps extend this capability by curing the adhesive almost instantly. Using a cyanoacrylate activator it also enables fillets of cured adhesive to be formed if required and can be used to reduce the effects of blooming, which can affect decorative surfaces. CA-1 is particularly effective when bonding porous materials, as the rapid curing prevents the adhesive from soaking in and ensures a stronger more reliable bond.\u003c\/p\u003e\n\u003ch3\u003eApplications and Uses\u003c\/h3\u003e\n\u003cp\u003eNEXTITE 580 has been designed as a rubber toughened instant adhesive for improved impact resistance, shear and peel strengths. It is ideal for industries and tasks that require a reliable flexible adhesive with fast bonding and high strength. It is perfect for bonding two materials that expand and contract at different rates as it handles the thermal expansion well. It is suitable for jobs that require a longer fixture time to allow for alignment of parts.\u003c\/p\u003e\n\u003ch3\u003eTools and Accessories\u003c\/h3\u003e\n\u003cp\u003eThe 20g and 50g bottles are specifically designed to work with a variety of nozzles and tips, so users can adapt the application method without the need to transfer the adhesive into another container. The nozzles come in a variety of internal diameters and lengths for all types of applications. They easily press-fit directly onto the tip of the instant adhesive bottle. The benefit of using alternative tips is that it gives users greater control, allowing only a precise amount of adhesive to be dispensed. They also extend the reach of the bottle, making it easier to apply adhesive accurately in tight spaces or detailed applications. \u003c\/p\u003e\n\u003cp\u003eFor NEXTITE 580, we recommend either the 0.6mm or 0.8mm tips or nozzles.\u003c\/p\u003e\n\u003ch3\u003eTechnical Highlights\u003c\/h3\u003e\n\u003cdiv class=\"TablePress\" data-table=\"58840\"\u003e\u003c\/div\u003e\n\u003ch3\u003eInstructions for use\u003c\/h3\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e1.     \u003c!--[endif]--\u003eEnsure all bonding surfaces are clean and free of grease. Use NEXTITE PROPREP or ACRI-BOND CLEANER (for delicate materials) and allow the surfaces to dry completely.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e2.     \u003c!--[endif]--\u003eFor low surface energy plastics, apply NEXTITE SP 901 Primer to the bonding area. Use sparingly and avoid excess application. Let the primer dry fully. Do not use primer on plastics that are not low surface energy.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e3.     \u003c!--[endif]--\u003eIf required, NEXTITE CA-1 Activator can be applied. Apply to one bonding surface only. If a primer has been used, do not apply activator to the same area. Allow the activator to dry before proceeding.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e4.     \u003c!--[endif]--\u003eDispense adhesive onto one surface only (never on the surface treated with activator). Assemble the components quickly, as the rapid fixture time provides little chance for repositioning.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e5.     \u003c!--[endif]--\u003eTo cure excess adhesive or fillets outside the bond line, apply NEXTITE CA-1 Activator by spraying or dropping directly onto the exposed adhesive.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e6.     \u003c!--[endif]--\u003eKeep the parts fixed or clamped in position until the adhesive has achieved fixture.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e7.     \u003c!--[endif]--\u003eAllow the bond to reach full strength before applying service loads, which typically occurs after 24 to 72 hours depending on the bond line, substrates and environmental conditions.\u003c\/p\u003e\n\u003ch3\u003eShelf Life, Storage and Pack Size\u003c\/h3\u003e\n\u003cp\u003eNEXTITE 580 has an 18 Month Shelf Life when stored correctly.\u003c\/p\u003e\n\u003cp\u003eStore in a cool dry place out of direct sunlight, an enclosed cabinet is recommended, to extend the shelf life of this product. Keep the open container tightly closed do not leave open.\u003c\/p\u003e\n\u003cp\u003eOur Specialised Instant Adhesives come in three size options 20g, 50g and 500g.\u003c\/p\u003e\n\u003ch3\u003eDownloads\u003c\/h3\u003e\n\u003cp\u003eNEXTITE 580 Technical Data Sheet | NEXTITE 580 Material Safety Data Sheet\u003c\/p\u003e","brand":"NEXTITE","offers":[{"title":"20g","offer_id":46476915507349,"sku":"58020","price":19.6,"currency_code":"AUD","in_stock":true},{"title":"50g","offer_id":46476915540117,"sku":"58050","price":38.9,"currency_code":"AUD","in_stock":true},{"title":"500g","offer_id":46476915572885,"sku":"580500","price":198.5,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0740\/9834\/4085\/files\/NEXTITE_580_20g_33764942-d8ae-4a87-b05e-663b5eef4c59.jpg?v=1771381060"},{"product_id":"nextite-proprep","title":"NEXTITE PROPREP Surface Preparation Cleaner","description":"\u003cp\u003eNEXTITE PROPREP is a high performance surface preparation cleaner formulated for rapid evaporation and residue free results. It lifts oils, greases, adhesive residue and contamination to ensure optimal bond strength before applying adhesives, sealants or tapes. It also performs as a safe general purpose cleaner for tools, equipment and maintenance tasks. Safe on plastics, metals, powder coated finishes and sensitive substrates when used as directed.\u003c\/p\u003e\n\u003ch3\u003eProduct Overview\u003c\/h3\u003e\n\u003cp\u003eNEXTITE PROPREP Surface Preparation Cleaner is formulated to maximize adhesion results by delivering a clean and contaminant free substrate. It flashes off quickly and leaves no residue behind, no post preparation necessary. PROPREP cuts through dust and dirt, grease, oils, adhesive residue and general surface contamination so parts can be prepared with confidence.\u003c\/p\u003e\n\u003cp\u003eIts delicate formulation makes it suitable for a range of materials such as: metals, plastics, composites and coated surfaces. Whether you are using our adhesives or sealants, NEXTITE PROPREP establishes a reliable starting point for any application. The fast evaporation rate supports efficient workflows and reduces downtime while still providing enough working time for a thorough wipe down.\u003c\/p\u003e\n\u003cp\u003eNEXTITE PROPREP is an essential preparation for professional bonding results. Delicate on substrates, Tough on surface contamination.\u003c\/p\u003e\n\u003ch3\u003eApplications and Uses\u003c\/h3\u003e\n\u003cp\u003eIdeal for preparing surfaces prior to applying adhesives, sealants or tapes. Quickly removes oils, grease, silicones, contaminants and adhesive residue from production parts, signage materials, automotive components and general industrial surfaces.\u003c\/p\u003e\n\u003ch3\u003eInstructions for Use\u003c\/h3\u003e\n\u003cp\u003eSpray directly onto the surface and allow the contamination to breakdown. Either wipe away while the cleaner is still wet, or allow it to evaporate then remove loosened residue with a clean lint free cloth. Repeat the process for heavy build up. Always test on a small hidden area before full scale use.\u003c\/p\u003e\n\u003ch3\u003eDownloads\u003c\/h3\u003e\n\u003cp\u003eNEXTITE PROPREP Technical Data Sheet | NEXTITE PROPREP Material Safety Data Sheet\u003c\/p\u003e","brand":"NEXTITE","offers":[{"title":"Single","offer_id":46674242961557,"sku":"NEXTITE-PROPREP-1","price":22.75,"currency_code":"AUD","in_stock":true},{"title":"Box of 12","offer_id":46674242994325,"sku":"NEXTITE-PROPREP-12","price":231.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0740\/9834\/4085\/files\/NEXTITEPROPREP.jpg?v=1770615798"},{"product_id":"nextite-535","title":"NEXTITE 535 Impact Resistant, Clear Rubber Toughened","description":"\u003cp\u003eNEXTITE 535 is a high performance clear rubber toughened instant adhesive designed for superior durability and reliability. Its advanced rubber toughened formulation provides exceptional impact, peel and sheer strength, creating resilient bonds that can withstand demanding conditions and vibrations. The medium viscosity ensures controlled application whilst the medium cure time of 30 – 45 seconds gives users some extra time to position and align components before fixturing. NEXTITE 535 delivers excellent adhesion to a wide variety of materials including plastics, metals and rubbers. It's clear formulation makes it suitable for medical, electronic and precision applications where flexibility, bond line visibility and aesthetics are critical.\u003c\/p\u003e\n\u003ch4\u003eProduct Overview\u003c\/h4\u003e\n\u003cp\u003eNEXTITE 535 is a rubber toughened instant adhesive designed for applications that require superior durability and flexibility. Its clear rubber toughened formulation provides exceptional impact resistance and greatly improves the peel and shear strength, ensuring reliable performance even under stress or vibration. The adhesive maintains good elasticity, allowing bonded joints to flex and move without failure, which is especially important when bonding dissimilar materials that expand or contract at different rates. This combination of strength and flexibility makes NEXTITE 535 ideal for assemblies subject to dynamic loads, temperature changes or movement in service.\u003c\/p\u003e\n\u003cp\u003eWith a medium viscosity of 100 – 250 CPS at 25°C, NEXTITE 535 offers excellent control during application, reducing mess and ensuring accurate adhesive placement. Its medium fixture time of 30 – 45 seconds depending on material, gives users the ability to position and align parts before the bond sets. This formulation provides gap filling of up to 0.20 mm and can withstand high temperatures of up to 120°C. It is ideal for a wide range of applications including bonding plastics, metals and rubbers. NEXTITE 535 is very high strength on close fitting parts.\u003c\/p\u003e\n\u003ch6\u003eNEXTITE SP 901 Polyolefin Primer\u003c\/h6\u003e\n\u003cp\u003eNEXTITE SP 901 is a surface primer for making polyolefins and other low surface energy surfaces suitable for bonding with NEXTITE Instant Adhesives. It is suitable to prime the notoriously difficult to bond surfaces such as polyethylene, polypropylene and polytetrafluoroethylene (PTFE). NEXTITE SP 901 works well with all of our cyanoacrylate adhesives especially the faster fixture time ones.\u003c\/p\u003e\n\u003ch6\u003eNEXTITE CA-1 Cyanoacrylate Activator\u003c\/h6\u003e\n\u003cp\u003eNEXTITE CA-1 can be used in conjunction with NEXTITE Cyanoacrylate Adhesives to promote a faster cure and to extend their gap-filling capabilities. Cyanoacrylate Adhesives naturally have limited gap-filling ability, but the use of an activator helps extend this capability by curing the adhesive almost instantly. Using a cyanoacrylate activator it also enables fillets of cured adhesive to be formed if required and can be used to reduce the effects of blooming, which can affect decorative surfaces. CA-1 is particularly effective when bonding porous materials, as the rapid curing prevents the adhesive from soaking in and ensures a stronger more reliable bond.\u003c\/p\u003e\n\u003ch4\u003eApplications and Uses\u003c\/h4\u003e\n\u003cp\u003eNEXTITE 535 has been designed as a rubber toughened instant adhesive for improved impact resistance, shear and peel strengths. It is ideal for industries and tasks that require a reliable flexible adhesive with fast bonding and high strength. It is perfect for bonding two materials that expand and contract at different rates as it handles the thermal expansion well. It is suitable for jobs that require a medium fixture time to allow for alignment of parts.\u003c\/p\u003e\n\u003ch4\u003eTools and Accessories\u003c\/h4\u003e\n\u003cp\u003eThe 20g and 50g bottles are specifically designed to work with a variety of nozzles and tips, so users can adapt the application method without the need to transfer the adhesive into another container. The nozzles come in a variety of internal diameters and lengths for all types of applications. They easily press-fit directly onto the tip of the instant adhesive bottle. The benefit of using alternative tips is that it gives users greater control, allowing only a precise amount of adhesive to be dispensed. They also extend the reach of the bottle, making it easier to apply adhesive accurately in tight spaces or detailed applications. \u003c\/p\u003e\n\u003cp\u003eFor NEXTITE 535, we recommend either the 0.6mm or 0.8mm tips or nozzles.\u003c\/p\u003e\n\u003ch4\u003eTechnical Highlights\u003c\/h4\u003e\n\u003cdiv class=\"TablePress\" data-table=\"60116\"\u003e\u003c\/div\u003e\n\u003ch4\u003eInstructions for use\u003c\/h4\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e1.     \u003c!--[endif]--\u003eEnsure all bonding surfaces are clean and free of grease. Use NEXTITE PROPREP or ACRI-BOND CLEANER (for delicate materials) and allow the surfaces to dry completely.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e2.     \u003c!--[endif]--\u003eFor low surface energy plastics, apply NEXTITE SP 901 Primer to the bonding area. Use sparingly and avoid excess application. Let the primer dry fully. Do not use primer on plastics that are not low surface energy.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e3.     \u003c!--[endif]--\u003eIf required, NEXTITE CA-1 Activator can be applied. Apply to one bonding surface only. If a primer has been used, do not apply activator to the same area. Allow the activator to dry before proceeding.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e4.     \u003c!--[endif]--\u003eDispense adhesive onto one surface only (never on the surface treated with activator). Assemble the components quickly, as the rapid fixture time provides little chance for repositioning.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e5.     \u003c!--[endif]--\u003eTo cure excess adhesive or fillets outside the bond line, apply NEXTITE CA-1 Activator by spraying or dropping directly onto the exposed adhesive.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e6.     \u003c!--[endif]--\u003eKeep the parts fixed or clamped in position until the adhesive has achieved fixture.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e7.     \u003c!--[endif]--\u003eAllow the bond to reach full strength before applying service loads, which typically occurs after 24 to 72 hours depending on the bond line, substrates and environmental conditions.\u003c\/p\u003e\n\u003ch4\u003eShelf Life, Storage and Pack Size\u003c\/h4\u003e\n\u003cp\u003eNEXTITE 535 has an 18 Month Shelf Life when stored correctly.\u003c\/p\u003e\n\u003cp\u003eStore in a cool dry place out of direct sunlight, an enclosed cabinet is recommended, to extend the shelf life of this product. Keep the open container tightly closed do not leave open.\u003c\/p\u003e\n\u003cp\u003eOur Specialised Instant Adhesives come in three size options 20g, 50g and 500g.\u003c\/p\u003e\n\u003ch4\u003eDownloads\u003c\/h4\u003e\n\u003cp\u003eNEXTITE 535 Technical Data Sheet | NEXTITE 535 Material Safety Data Sheet\u003c\/p\u003e","brand":"NEXTITE","offers":[{"title":"20g","offer_id":46832044048533,"sku":"53520","price":23.4,"currency_code":"AUD","in_stock":true},{"title":"50g","offer_id":46832044081301,"sku":"53550","price":46.45,"currency_code":"AUD","in_stock":true},{"title":"500g","offer_id":46832044114069,"sku":"535500","price":237.6,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0740\/9834\/4085\/files\/NEXTITE_535_20g.jpg?v=1771381060"},{"product_id":"nextite-510","title":"NEXTITE 510 Impact Resistant, Thick Black Rubber Toughened","description":"\u003cp\u003eNEXTITE 510 is a high performance black rubber toughened instant adhesive designed for superior durability and reliability. Its advanced rubber toughened formulation provides exceptional impact, peel and sheer strength, creating resilient bonds that can withstand demanding conditions and vibrations. The high viscosity ensures precise application whilst the slower cure time of 60 seconds which allows users some extra time to position and align components before fixturing. NEXTITE 510 delivers excellent adhesion to a wide variety of materials including plastics, metals and rubbers.\u003c\/p\u003e\n\u003ch4\u003eProduct Overview\u003c\/h4\u003e\n\u003cp\u003eNEXTITE 510 is a rubber toughened instant adhesive designed for applications that require superior durability and flexibility. Its rubber toughened formulation provides exceptional impact resistance and greatly improves the peel and shear strength, ensuring reliable performance even under stress or vibration. The adhesive maintains good elasticity, allowing bonded joints to flex and move without failure, which is especially important when bonding dissimilar materials that expand or contract at different rates. This combination of strength and flexibility makes NEXTITE 510 ideal for assemblies subject to dynamic loads, temperature changes or movement in service.\u003c\/p\u003e\n\u003cp\u003eWith a high viscosity of 1700 – 5000 CPS at 25°C, NEXTITE 510 offers excellent control during application, reducing mess and ensuring accurate adhesive placement. Its longer fixture time of 60 seconds depending on material, gives users the ability to position and align parts before the bond sets. This formulation provides gap filling of up to 0.20 mm and can withstand temperatures of up to 100°C (for higher temperature resistance consider NEXTITE 5210 for up to 120°C temperatures). It is ideal for a wide range of applications including bonding plastics, metals and rubbers. NEXTITE 510 is very high strength on close fitting parts.\u003c\/p\u003e\n\u003ch6\u003eNEXTITE SP 901 Polyolefin Primer\u003c\/h6\u003e\n\u003cp\u003eNEXTITE SP 901 is a surface primer for making polyolefins and other low surface energy surfaces suitable for bonding with NEXTITE Instant Adhesives. It is suitable to prime the notoriously difficult to bond surfaces such as polyethylene, polypropylene and polytetrafluoroethylene (PTFE). NEXTITE SP 901 works well with all of our cyanoacrylate adhesives especially the faster fixture time ones.\u003c\/p\u003e\n\u003ch6\u003eNEXTITE CA-1 Cyanoacrylate Activator\u003c\/h6\u003e\n\u003cp\u003eNEXTITE CA-1 can be used in conjunction with NEXTITE Cyanoacrylate Adhesives to promote a faster cure and to extend their gap-filling capabilities. Cyanoacrylate Adhesives naturally have limited gap-filling ability, but the use of an activator helps extend this capability by curing the adhesive almost instantly. Using a cyanoacrylate activator it also enables fillets of cured adhesive to be formed if required and can be used to reduce the effects of blooming, which can affect decorative surfaces. CA-1 is particularly effective when bonding porous materials, as the rapid curing prevents the adhesive from soaking in and ensures a stronger more reliable bond.\u003c\/p\u003e\n\u003ch4\u003eApplications and Uses\u003c\/h4\u003e\n\u003cp\u003eNEXTITE 510 has been designed as a rubber toughened instant adhesive for improved impact resistance, shear and peel strengths. It is ideal for industries and tasks that require a reliable flexible adhesive with fast bonding and high strength. It is perfect for bonding two materials that expand and contract at different rates as it handles the thermal expansion well. It is suitable for jobs that require a longer fixture time to allow for alignment of parts.\u003c\/p\u003e\n\u003ch4\u003eTools and Accessories\u003c\/h4\u003e\n\u003cp\u003eThe 20g and 50g bottles are specifically designed to work with a variety of nozzles and tips, so users can adapt the application method without the need to transfer the adhesive into another container. The nozzles come in a variety of internal diameters and lengths for all types of applications. They easily press-fit directly onto the tip of the instant adhesive bottle. The benefit of using alternative tips is that it gives users greater control, allowing only a precise amount of adhesive to be dispensed. They also extend the reach of the bottle, making it easier to apply adhesive accurately in tight spaces or detailed applications. \u003c\/p\u003e\n\u003cp\u003eFor NEXTITE 510, we recommend either the 0.80mm or 1.20mm tips or nozzles.\u003c\/p\u003e\n\u003ch4\u003eTechnical Highlights\u003c\/h4\u003e\n\u003cdiv class=\"TablePress\" data-table=\"60010\"\u003e\u003cbr\u003e\u003c\/div\u003e\n\u003ch4\u003eInstructions for use\u003c\/h4\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e1.     \u003c!--[endif]--\u003eEnsure all bonding surfaces are clean and free of grease. Use NEXTITE PROPREP and allow the surfaces to dry completely.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e2.     \u003c!--[endif]--\u003eFor low surface energy plastics, apply NEXTITE SP 901 Primer to the bonding area. Use sparingly and avoid excess application. Let the primer dry fully. Do not use primer on plastics that are not low surface energy.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e3.     \u003c!--[endif]--\u003eIf required, NEXTITE CA-1 Activator can be applied. Apply to one bonding surface only. If a primer has been used, do not apply activator to the same area. Allow the activator to dry before proceeding.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e4.     \u003c!--[endif]--\u003eDispense adhesive onto one surface only (never on the surface treated with activator). Assemble the components quickly, as the rapid fixture time provides little chance for repositioning.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e5.     \u003c!--[endif]--\u003eTo cure excess adhesive or fillets outside the bond line, apply NEXTITE CA-1 Activator by spraying or dropping directly onto the exposed adhesive.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e6.     \u003c!--[endif]--\u003eKeep the parts fixed or clamped in position until the adhesive has achieved fixture.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e7.     \u003c!--[endif]--\u003eAllow the bond to reach full strength before applying service loads, which typically occurs after 24 to 72 hours depending on the bond line, substrates and environmental conditions.\u003c\/p\u003e\n\u003ch4\u003eShelf Life, Storage and Pack Size\u003c\/h4\u003e\n\u003cp\u003eNEXTITE 510 has an 18 Month Shelf Life when stored correctly.\u003c\/p\u003e\n\u003cp\u003eStore in a cool dry place out of direct sunlight, an enclosed cabinet is recommended, to extend the shelf life of this product. Keep the open container tightly closed do not leave open.\u003c\/p\u003e\n\u003cp\u003eOur Specialised Instant Adhesives come in three size options 20g, 50g and 500g.\u003c\/p\u003e\n\u003ch4\u003eDownloads\u003c\/h4\u003e\n\u003cp\u003eNEXTITE 510 Technical Data Sheet | NEXTITE 510 Material Safety Data Sheet\u003c\/p\u003e","brand":"NEXTITE","offers":[{"title":"20g","offer_id":46831509635221,"sku":"51020","price":23.4,"currency_code":"AUD","in_stock":true},{"title":"50g","offer_id":46831509667989,"sku":"51050","price":46.45,"currency_code":"AUD","in_stock":true},{"title":"500g","offer_id":46831509700757,"sku":"510500","price":237.6,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0740\/9834\/4085\/files\/NEXTITE_510_20g.jpg?v=1771381060"},{"product_id":"nextite-506","title":"NEXTITE 506 Surface Insensitive, Wicking Grade","description":"\u003cp\u003eNEXTITE 506 is a high performance surface insensitive instant adhesive meaning it delivers high strength, reliable bonds across a wide range of materials making it an ideal general purpose solution. With its ultra-low viscosity and fast cure speed, it sets in seconds on most substrates, providing virtually instant bonding on a wide range of materials including plastics, metals and rubbers. The surface insensitive formulation ensures consistent results even on rough, porous and acidic surfaces. While its high temperature resistance of up to 120°C makes it suitable for demanding applications. Due to the ultra-low viscosity it allows for wicking into material joints. \u003c\/p\u003e\n\u003ch4\u003eProduct Overview\u003c\/h4\u003e\n\u003cp\u003eNEXTITE 506 is a surface insensitive instant adhesive which provides dependable bonding even on difficult substrates. It’s all around general purpose formulation makes it ideal for a wide range of applications including bonding plastics, metals and rubbers. Its surface insensitive formulation allows for bonding on rough, porous and acidic surfaces where other instant adhesives fall short. In addition to this, NEXTITE 506 offers excellent heat resistance, maintaining strong adhesion at temperatures up to 120°C. Perfect for both high strength bonding applications and any fast at home jobs or repairs.\u003c\/p\u003e\n\u003cp\u003eNEXTITE 506 has an ultra-low viscosity 15 – 25 CPS at 25°C, allowing the adhesive to wick rapidly into tight gaps, capillary joints and pre assembled components. It can also be applied in a traditional manner and due to its ultra low viscosity it cures virtually instantly, typically faster than NEXTITE 501. NEXTITE 506 achieves strong bonds on most substrates in approximately 15 seconds, making it ideal for high speed assembly. It is capable of gap filling up to 0.10 mm and delivers very high strength on close fitting parts where precise alignment is critical.\u003c\/p\u003e\n\u003ch6\u003eNEXTITE SP 901 Polyolefin Primer\u003c\/h6\u003e\n\u003cp\u003eNEXTITE SP 901 is a surface primer for making polyolefins and other low surface energy surfaces suitable for bonding with NEXTITE Instant Adhesives. It is suitable to prime the notoriously difficult to bond surfaces such as polyethylene, polypropylene and polytetrafluoroethylene (PTFE). NEXTITE SP 901 works well with all of our cyanoacrylate adhesives especially the faster fixture time ones.\u003c\/p\u003e\n\u003ch6\u003e NEXTITE CA-1 Cyanoacrylate Activator\u003c\/h6\u003e\n\u003cp\u003eNEXTITE CA-1 can be used in conjunction with NEXTITE Cyanoacrylate Adhesives to promote a faster cure and to extend their gap-filling capabilities. Cyanoacrylate Adhesives naturally have limited gap-filling ability, but the use of an activator helps extend this capability by curing the adhesive almost instantly. Using a cyanoacrylate activator it also enables fillets of cured adhesive to be formed if required and can be used to reduce the effects of blooming, which can affect decorative surfaces. CA-1 is particularly effective when bonding porous materials, as the rapid curing prevents the adhesive from soaking in and ensures a stronger more reliable bond. \u003c\/p\u003e\n\u003ch4\u003eApplications and Uses\u003c\/h4\u003e\n\u003cp\u003eNEXTITE 506 has been designed as a surface insensitive instant adhesive. It is ideal for industries and tasks that require a general purpose adhesive with instant bond and high strength. It is also ideal for surfaces that have a rough, porous or acidic surface making this adhesive a true allrounder. It's ultra low viscosity allows for wicking into preassembled tight fitting parts.\u003c\/p\u003e\n\u003ch4\u003eTools and Accessories\u003c\/h4\u003e\n\u003cp\u003eThe 20g and 50g bottles are specifically designed to work with a variety of nozzles and tips, so users can adapt the application method without the need to transfer the adhesive into another container. The nozzles come in a variety of internal diameters and lengths for all types of applications. They easily press-fit directly onto the tip of the instant adhesive bottle. The benefit of using alternative tips is that it gives users greater control, allowing only a precise amount of adhesive to be dispensed. They also extend the reach of the bottle, making it easier to apply adhesive accurately in tight spaces or detailed applications. \u003c\/p\u003e\n\u003cp\u003eFor NEXTITE 506, we recommend either the 0.25mm, 0.40mm or 0.6mm tips or nozzles.\u003c\/p\u003e\n\u003ch4\u003eTechnical Highlights\u003c\/h4\u003e\n\u003cdiv class=\"TablePress\" data-table=\"60117\"\u003e\u003cbr\u003e\u003c\/div\u003e\n\u003ch4\u003eInstructions for use\u003c\/h4\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e1.     \u003c!--[endif]--\u003eEnsure all bonding surfaces are clean and free of grease. Use NEXTITE PROPREP or ACRI-BOND CLEANER (for delicate materials) and allow the surfaces to dry completely.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e2.     \u003c!--[endif]--\u003eFor low surface energy plastics, apply NEXTITE SP 901 Primer to the bonding area. Use sparingly and avoid excess application. Let the primer dry fully. Do not use primer on plastics that are not low surface energy.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e3.     \u003c!--[endif]--\u003eIf required, NEXTITE CA-1 Activator can be applied. Apply to one bonding surface only. If a primer has been used, do not apply activator to the same area. Allow the activator to dry before proceeding.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e4.     \u003c!--[endif]--\u003eDispense adhesive onto one surface only (never on the surface treated with activator). Assemble the components quickly, as the rapid fixture time provides little chance for repositioning.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e5.     \u003c!--[endif]--\u003eTo cure excess adhesive or fillets outside the bond line, apply NEXTITE CA-1 Activator by spraying or dropping directly onto the exposed adhesive.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e6.     \u003c!--[endif]--\u003eKeep the parts fixed or clamped in position until the adhesive has achieved fixture.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e7.     \u003c!--[endif]--\u003eAllow the bond to reach full strength before applying service loads, which typically occurs after 24 to 72 hours depending on the bond line, substrates and environmental conditions.\u003c\/p\u003e\n\u003ch4\u003eShelf Life, Storage and Pack Size\u003c\/h4\u003e\n\u003cp\u003eNEXTITE 506 has an 18 Month Shelf Life when stored correctly.\u003c\/p\u003e\n\u003cp\u003eStore in a cool dry place out of direct sunlight, an enclosed cabinet is recommended, to extend the shelf life of this product. Keep the open container tightly closed do not leave open.\u003c\/p\u003e\n\u003cp\u003eOur Specialised Instant Adhesives come in three size options 20g, 50g and 500g.\u003c\/p\u003e\n\u003ch4\u003eDownloads\u003c\/h4\u003e\n\u003cp style=\"line-height: 150%;\" class=\"MsoNormal\"\u003eNEXTITE 506 Technical Data Sheet | NEXTITE 506 Material Safety Data Sheet\u003c\/p\u003e","brand":"NEXTITE","offers":[{"title":"20g","offer_id":46832350986389,"sku":"50620","price":16.7,"currency_code":"AUD","in_stock":true},{"title":"50g","offer_id":46832351019157,"sku":"50650","price":31.9,"currency_code":"AUD","in_stock":true},{"title":"500g","offer_id":46832351051925,"sku":"506500","price":159.5,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0740\/9834\/4085\/files\/NEXTITE_506_20g.jpg?v=1771381060"},{"product_id":"nextite-5210-high-temp-and-impact-resistant-black-rubber-toughened","title":"NEXTITE 5210 High Temp and Impact Resistant, Black Rubber Toughened","description":"\u003cp\u003eNEXTITE 5210 is a high performance high temperature resistant, black rubber toughened instant adhesive designed for superior durability and reliability. Its advanced rubber toughened formulation provides exceptional impact, peel and sheer strength, creating resilient bonds that can withstand demanding conditions and vibrations. The medium viscosity ensures controlled application whilst the slower cure time of 60 – 90 seconds gives users some extra time to position and align components before fixturing. It offers sustained temperature resistance of up to 120°C, making it suitable for applications exposed to elevated heat and thermal cycling. NEXTITE 5210 delivers excellent adhesion to a wide variety of materials including plastics, metals and rubbers.\u003c\/p\u003e\n\u003ch3\u003eProduct Overview\u003c\/h3\u003e\n\u003cp\u003eNEXTITE 5210 is a rubber toughened instant adhesive designed for applications that require superior durability and flexibility. Its rubber toughened formulation provides exceptional impact resistance and greatly improves the peel and shear strength, ensuring reliable performance even under stress or vibration. The adhesive maintains good elasticity, allowing bonded joints to flex and move without failure, which is especially important when bonding dissimilar materials that expand or contract at different rates. This combination of strength and flexibility makes NEXTITE 5210 ideal for assemblies subject to dynamic loads, temperature changes or movement in service.\u003c\/p\u003e\n\u003cp\u003eWith a medium viscosity of 100 – 250 CPS at 25°C, NEXTITE 5210 offers excellent control during application, reducing mess and ensuring accurate adhesive placement. Its longer fixture time of 60 – 90 seconds depending on material, gives users the ability to position and align parts before the bond sets. This formulation provides gap filling of up to 0.20 mm and can withstand temperatures of up to 120°C. It is ideal for a wide range of applications including bonding plastics, metals and rubbers. NEXTITE 5210 is very high strength on close fitting parts.\u003c\/p\u003e\n\u003ch5\u003eNEXTITE SP 901 Polyolefin Primer\u003c\/h5\u003e\n\u003cp\u003eNEXTITE SP 901 is a surface primer for making polyolefins and other low surface energy surfaces suitable for bonding with NEXTITE Instant Adhesives. It is suitable to prime the notoriously difficult to bond surfaces such as polyethylene, polypropylene and polytetrafluoroethylene (PTFE). NEXTITE SP 901 works well with all of our cyanoacrylate adhesives especially the faster fixture time ones.\u003c\/p\u003e\n\u003ch5\u003eNEXTITE CA-1 Cyanoacrylate Activator\u003c\/h5\u003e\n\u003cp\u003eNEXTITE CA-1 can be used in conjunction with NEXTITE Cyanoacrylate Adhesives to promote a faster cure and to extend their gap-filling capabilities. Cyanoacrylate Adhesives naturally have limited gap-filling ability, but the use of an activator helps extend this capability by curing the adhesive almost instantly. Using a cyanoacrylate activator it also enables fillets of cured adhesive to be formed if required and can be used to reduce the effects of blooming, which can affect decorative surfaces. CA-1 is particularly effective when bonding porous materials, as the rapid curing prevents the adhesive from soaking in and ensures a stronger more reliable bond.\u003c\/p\u003e\n\u003ch3\u003eApplications and Uses\u003c\/h3\u003e\n\u003cp\u003eNEXTITE 5210 has been designed as a rubber toughened instant adhesive for improved impact resistance, shear and peel strengths as well as perform well in environments with elevated temperatures. It is ideal for industries and tasks that require a reliable flexible adhesive with fast bonding and high strength. It is perfect for bonding two materials that expand and contract at different rates as it handles the thermal expansion well. It is suitable for jobs that require a longer fixture time to allow for alignment of parts.\u003c\/p\u003e\n\u003ch3\u003eTools and Accessories\u003c\/h3\u003e\n\u003cp\u003eThe 20g and 50g bottles are specifically designed to work with a variety of nozzles and tips, so users can adapt the application method without the need to transfer the adhesive into another container. The nozzles come in a variety of internal diameters and lengths for all types of applications. They easily press-fit directly onto the tip of the instant adhesive bottle. The benefit of using alternative tips is that it gives users greater control, allowing only a precise amount of adhesive to be dispensed. They also extend the reach of the bottle, making it easier to apply adhesive accurately in tight spaces or detailed applications. \u003c\/p\u003e\n\u003cp\u003eFor NEXTITE 5210, we recommend either the 0.6mm or 0.8mm tips or nozzles.\u003c\/p\u003e\n\u003ch3\u003eTechnical Highlights\u003c\/h3\u003e\n\u003cdiv class=\"TablePress\" data-table=\"60115\"\u003e\u003cbr\u003e\u003c\/div\u003e\n\u003ch3\u003eInstructions for use\u003c\/h3\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e1.     \u003c!--[endif]--\u003eEnsure all bonding surfaces are clean and free of grease. Use NEXTITE PROPREP or ACRI-BOND CLEANER (for delicate materials) and allow the surfaces to dry completely.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e2.     \u003c!--[endif]--\u003eFor low surface energy plastics, apply NEXTITE SP 901 Primer to the bonding area. Use sparingly and avoid excess application. Let the primer dry fully. Do not use primer on plastics that are not low surface energy.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e3.     \u003c!--[endif]--\u003eIf required, NEXTITE CA-1 Activator can be applied. Apply to one bonding surface only. If a primer has been used, do not apply activator to the same area. Allow the activator to dry before proceeding.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e4.     \u003c!--[endif]--\u003eDispense adhesive onto one surface only (never on the surface treated with activator). Assemble the components quickly, as the rapid fixture time provides little chance for repositioning.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e5.     \u003c!--[endif]--\u003eTo cure excess adhesive or fillets outside the bond line, apply NEXTITE CA-1 Activator by spraying or dropping directly onto the exposed adhesive.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e6.     \u003c!--[endif]--\u003eKeep the parts fixed or clamped in position until the adhesive has achieved fixture.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e7.     \u003c!--[endif]--\u003eAllow the bond to reach full strength before applying service loads, which typically occurs after 24 to 72 hours depending on the bond line, substrates and environmental conditions.\u003c\/p\u003e\n\u003ch3\u003eShelf Life, Storage and Pack Size\u003c\/h3\u003e\n\u003cp\u003eNEXTITE 5210 has an 18 Month Shelf Life when stored correctly.\u003c\/p\u003e\n\u003cp\u003eStore in a cool dry place out of direct sunlight, an enclosed cabinet is recommended, to extend the shelf life of this product. Keep the open container tightly closed do not leave open.\u003c\/p\u003e\n\u003cp\u003eOur Specialised Instant Adhesives come in three size options 20g, 50g and 500g.\u003c\/p\u003e\n\u003ch3\u003eDownloads\u003c\/h3\u003e\n\u003cp\u003eNEXTITE 5210 Technical Data Sheet | NEXTITE 5210 Material Safety Data Sheet\u003c\/p\u003e","brand":"NEXTITE","offers":[{"title":"20g","offer_id":46832308977813,"sku":"521020","price":23.4,"currency_code":"AUD","in_stock":true},{"title":"50g","offer_id":46832309010581,"sku":"521050","price":46.45,"currency_code":"AUD","in_stock":true},{"title":"500g","offer_id":46832309043349,"sku":"5210500","price":237.6,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0740\/9834\/4085\/files\/NEXTITE_5210_20g.jpg?v=1771381060"},{"product_id":"nextite-ab832","title":"NEXTITE AB832 Primerless Structural to Metals, Medium Cure","description":"\u003cp\u003eNEXTITE AB832 is an industrial-grade, two-part MMA adhesive offering primerless adhesion to metals, excellent fatigue resistance, high strength, medium cure time, non-sag and reliable bonding of plastics, metals, and composites with little to no surface preparation. Ideal for structural applications across multiple industries. Balanced thicker viscosity ensures smooth, precise application for diverse industrial bonding needs.\u003c\/p\u003e\n\u003ch3\u003eProduct Overview\u003c\/h3\u003e\n\u003cp\u003eNEXTITE AB832 is a high-performance, two-part methyl methacrylate (MMA) structural adhesive engineered for primerless adhesion to metals. Designed for reliable bonding of engineering plastics, metals, and composite materials, NEXTITE AB560 offers exceptional strength, toughness, fatigue and impact resistance. \u003c\/p\u003e\n\u003cp\u003eWith a medium working time of 11 to 13 minutes, this adhesive allows for efficient assembly without the need for extensive surface preparation or primers. It is particularly suited for bonding primerless to thermoplastics, powder-coated metals, raw metals, and composite assemblies where high strength and impact resistance are critical.\u003c\/p\u003e\n\u003cp\u003eUsing a primerless to metal MMA adhesive provides a fast and efficient alternative to traditional welding or mechanical fastening methods. Unlike welding, MMA adhesives do not create significant heat, which eliminates the risk of material distortion or burn through. They also allow dissimilar metals and substrates to be bonded to each other primerless. Stress is distributed evenly across the bonded area rather than concentrating it at a single point like a bolt or rivet. This results in stronger, more durable assemblies with improved vibration resistance, reduced corrosion risk and faster production times since no surface primers or complex mechanical preparation is required, can bond materials as received.\u003c\/p\u003e\n\u003cp\u003eNEXTITE AB832 delivers rapid strength development at room temperature, along with excellent toughness, fatigue resistance, and long-term durability. Its non-sag, highly thixotropic formula makes it ideal for precise application, even on vertical surfaces. It also provides high gap filling capabilities of up to 9mm. This adhesive is the go-to solution for industrial manufacturing, transportation, marine, and general assembly where consistent performance and high fatigue resistance are required. \u003c\/p\u003e\n\u003cp\u003eFor production environments where a shorter fixture time is critical, NEXTITE AB830 offers the same performance and material compatibility as NEXTITE AB832 but with a reduced working time of 4 to 6 minutes and a fixture time of 17 to 19 minutes. \u003c\/p\u003e\n\u003cp\u003eFor production environments where longer working times are critical, NEXTITE AB835 offers the same performance and material compatibility as NEXTITE AB832 but with an increased working time of 55 to 65 minutes and a fixture time of 100 to 120 minutes. \u003c\/p\u003e\n\u003ch3\u003eApplications and Uses\u003c\/h3\u003e\n\u003cp\u003eNEXTITE AB832 bonds to a variety of substrates without the need for primers they include but aren’t limited to:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003ePlastics: Acrylic (PMMA), Polycarbonate (PC), Acrylonitrile Butadiene Styrene (ABS), Polyvinyl Chloride (PVC)\u003c\/li\u003e\n\u003cli\u003eMetals: Aluminium, Steel, Stainless Steel, Powder Coated Surfaces\u003c\/li\u003e\n\u003cli\u003eComposites: Fibreglass Reinforced Plastic (FRP), Carbon Fibre (CF)\u003c\/li\u003e\n\u003cli\u003eOther: Glass\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eNEXTITE AB832 will not adhere to plastics with a low surface energy such as Polypropylene (PP), Polyethylene (PE) or Polyolefins. These plastics can be structurally adhered to with NEXTITE AB206 and NEXTITE Instant Adhesives also have a great bond when using NEXTITE SP 901 Primer.\u003c\/p\u003e\n\u003cp\u003eSome applications of NEXTITE AB832 include:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eTransport Industry: Used to bond metal and composites in vehicles like trucks, buses, trailers, and railcars.\u003c\/li\u003e\n\u003cli\u003eMarine: Bonds composite hulls, decks, and marine components with strong resistance to moisture and saltwater.\u003c\/li\u003e\n\u003cli\u003eSignage and Displays: Bonds plastic and metal parts in signs and displays for indoor and outdoor use.\u003c\/li\u003e\n\u003cli\u003eIndustrial Equipment: Used in machinery and appliance assembly for strong, impact- and vibration-resistant joints.\u003c\/li\u003e\n\u003cli\u003eAutomotive: Bonding structural or cosmetic repair of body panels, including re-bonding fibreglass or composite components.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eVersatility of NEXTITE AB832\u003c\/h3\u003e\n\u003cp\u003eWhile bond strength is important, it’s not the only factor to consider when selecting an adhesive. Once fully cured, NEXTITE AB832 delivers a range of additional benefits that can make a real difference depending on your application.\u003c\/p\u003e\n\u003cp\u003eWhen fully cured NEXTITE AB832 can be sanded, grinded, routed and polished to get your desired finish. You can even paint over it!\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eGreat Chemical Resistance\u003c\/li\u003e\n\u003cli\u003eHigh fatigue and impact resistance\u003c\/li\u003e\n\u003cli\u003eHigh resistance to weathering\u003c\/li\u003e\n\u003cli\u003eCan be used in indoor and outdoor applications\u003c\/li\u003e\n\u003cli\u003eHigh Temperature resistance -50 to 120°C\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eTools and Accessories\u003c\/h3\u003e\n\u003cp\u003eNEXTITE AB832 requires the use of a compatible dual cartridge dispensing applicator and static mixer nozzles, sold separately. Both the 50mL and 490mL Cartridges use standard 10:1 Ratio dual cartridge dispensing applicators and static mixers. It is important to use the correct applicator and mixer for each cartridge size, as 10:1 ratio systems are not compatible with other ratios cartridges and accessories. Each cartridge type requires the matching dispensing applicator and static mixer designed specifically for its ratio.\u003c\/p\u003e\n\u003ch4\u003e50mL Tubes\u003c\/h4\u003e\n\u003cp\u003eDispensing Applicator: Manual 50mL 10:1 Dispensing Applicator | Manual Hand Plunger for 10:1 50mL Cartridges (for one time use)\u003c\/p\u003e\n\u003cp\u003eStatic Mixer Nozzles: 10:1 50mL Quadro B Type (Standard Tip) | 10:1 50mL Quadro B Type (Narrow Tip)\u003c\/p\u003e\n\u003ch4\u003e400mL Tubes\u003c\/h4\u003e\n\u003cp\u003eDispensing Applicator: Manual 490mL 10:1 Dispensing Applicator | Pneumatic 490mL 10:1 Dispensing Applicator | Electric 490mL 10:1 Dispensing Applicator\u003c\/p\u003e\n\u003cp\u003eExtra Static Mixer Nozzles: 10:1 490mL Quadro F Type (Green – Orange Base)\u003c\/p\u003e\n\u003ch3\u003eTechnical Highlights\u003c\/h3\u003e\n\u003ctable border=\"1\" cellspacing=\"0\" cellpadding=\"0\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003eAdhesive Type\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003eMethyl Methacrylate\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003eColour\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003eGrey or Black\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003eMix Ratio\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003e10:1\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003eKey Substrates\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003eMetals, Plastics and Composites\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003eViscosity\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003e100,000 – 125,000 CPS\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003eMaximum Gap Fill\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003e9 mm\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003eWorking Time\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003e11 – 13 min\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003eFixture Time\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003e28 – 32 min\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003eFull Strength\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003e24 hrs\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003eSimilar Product\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003ePLEXUS ® MA832\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003eStrength Tests\u003c\/h3\u003e\n\u003ctable border=\"1\" cellspacing=\"0\" cellpadding=\"0\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003eSubstrate\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003eLap Shear Strength (psi)\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003eAluminium (Grit Blasted)\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003e2650\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003eStainless Steel\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003e2550\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003eSteel\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003e2500\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003eFRP\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003e1750\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003eChemical Resistance\u003c\/h3\u003e\n\u003ctable border=\"1\" cellspacing=\"0\" cellpadding=\"0\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003eResistant To\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003eSusceptible To\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003eHydrocarbons, Salt Solutions, Acids and Bases (3-10pH)\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd width=\"300\" valign=\"top\"\u003e\n\u003cp\u003ePolar Solvents, Strong Acids and Bases\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003eInstructions for use\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eUse a static mixer nozzle to accurately mix the contents of the 10:1 cartridge. Each cartridge includes one Static Mixer Nozzle 10:1, and you can purchase more in 5, 10 and 50 packs from our store.\u003c\/li\u003e\n\u003cli\u003eYou will also require a 10:1 Static Mixing Dispenser to push the contents through the static mixer. This is the best way to apply it and get accurate, dependable results every time.\u003c\/li\u003e\n\u003cli\u003eParts to be joined should fit without forcing and be clean, it is recommended to use NEXTITE PROPREP prior to applying any product to remove any oils, dust and dirt. It is important to let out any air bubbles and ensure adhesive is fully mixed by dispensing the first part of the cartridge onto some cardboard. This is to make sure the two separate parts are fully mixed and is generally the first 2-3mL. Apply adhesive directly from the static mixer.\u003c\/li\u003e\n\u003cli\u003ePress parts together in firm contact and use a clamp to secure while the glue reacts. NEXTITE AB832 will achieve a working strength within 28-32 min and full cure strength within 24 hours. You have approximately 11-13 minutes to work with the glue before it starts to set off.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003ePlease check the TDS for material suitability and strength of each bond. For a tutorial how to use please refer to our YouTube Chanel.\u003c\/p\u003e\n\u003ch3\u003eShelf Life, Storage and Pack Size\u003c\/h3\u003e\n\u003cp\u003eNEXTITE AB832 has a 12 Month Shelf Life when stored correctly.\u003c\/p\u003e\n\u003cp\u003eStore in a cool dry place out of direct sunlight, an enclosed cabinet is recommended, to extend the shelf life of this product. Keep the open container tightly closed do not leave open. \u003c\/p\u003e\n\u003cp\u003e50mL and 490mL Cartridges\u003c\/p\u003e\n\u003ch3\u003eDownloads\u003c\/h3\u003e\n\u003cp\u003eNEXTITE AB832 Technical Data Sheet | NEXTITE AB832 Material Safety Data Sheet\u003c\/p\u003e","brand":"NEXTITE","offers":[{"title":"50mL","offer_id":46854096224405,"sku":null,"price":36.85,"currency_code":"AUD","in_stock":true},{"title":"490mL","offer_id":46854096257173,"sku":null,"price":134.35,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0740\/9834\/4085\/files\/NEXTITEAB83250mL.jpg?v=1770618298"},{"product_id":"nextite-ab422","title":"NEXTITE AB422 High Toughness, Medium Cure","description":"\u003cp\u003eNEXTITE AB422 delivers high toughness and dependable performance when bonding plastics, metals and composites with minimal surface preparation. It provides excellent impact resistance and fatigue endurance with a medium working time of 11-13 minutes, making it ideal for structural and general assembly applications. The thicker viscosity allows for easy, controlled application across a wide range of materials. It is well suited for the transportation and marine industries as NEXTITE AB422 requires virtually no surface preparation and provides consistent overall performance.\u003c\/p\u003e\n\u003ch3\u003eProduct Overview\u003c\/h3\u003e\n\u003cp\u003eNEXTITE AB422 is a high-performance, two-part methyl methacrylate (MMA) structural adhesive engineered for demanding bonding applications. Designed for fast, reliable bonding of engineering plastics, metals, and composite materials, NEXTITE AB422 offers exceptional toughness, fatigue and impact resistance.\u003c\/p\u003e\n\u003cp\u003eWith a medium working time of 11 to 13 minutes, this adhesive allows for efficient assembly without the need for extensive surface preparation or primers. It is particularly suited for bonding thermoplastics, powder-coated metals, raw metals (full structural strength with NEXTITE SP120 MMA Metal Primer), and composite assemblies where high strength and impact resistance are critical.\u003c\/p\u003e\n\u003cp\u003eNEXTITE AB422 delivers rapid strength development at room temperature, along with excellent toughness, fatigue resistance, and long-term durability. Its non-sag, thixotropic formula makes it ideal for precise application, even on vertical surfaces. It also provides gap filling capabilities of up to 9mm. This adhesive is the go-to solution for industrial manufacturing, plastic fabrication, transportation, marine, and general assembly where consistent performance and high fatigue resistance are required.\u003c\/p\u003e\n\u003cp\u003eFor production environments where faster fixture times are critical, NEXTITE AB420 offers the same performance and material compatibility as NEXTITE AB422 but with a reduced working time of 4 to 6 minutes and a fixture time of 16 to 18 minutes.\u003c\/p\u003e\n\u003cp\u003eFor production environments where longer working times are critical, NEXTITE AB425 offers the same performance and material compatibility as NEXTITE AB422 but with an increased working time of 18 to 22 minutes and a fixture time of 48 to 54 minutes.\u003c\/p\u003e\n\u003ch3\u003eApplications and Uses\u003c\/h3\u003e\n\u003cp\u003eNEXTITE AB422 bonds to a variety of substrates they include but aren’t limited to:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003ePlastics: Acrylic (PMMA), Polycarbonate (PC), Acrylonitrile Butadiene Styrene (ABS), Polyvinyl Chloride (PVC)\u003c\/li\u003e\n\u003cli\u003eMetals: Aluminium, Steel, Stainless Steel, Powder Coated Surfaces (with NEXTITE SP120 Metal MMA Primer)\u003c\/li\u003e\n\u003cli\u003eComposites: Fibreglass Reinforced Plastic (FRP), Carbon Fibre (CF)\u003c\/li\u003e\n\u003cli\u003eOther: Glass\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eNEXTITE AB422 will not adhere to plastics with a low surface energy such as Polypropylene (PP), Polyethylene (PE) or Polyolefins. These plastics can be structurally adhered to with NEXTITE AB206 and NEXTITE Instant Adhesives also have a great bond when using NEXTITE SP 901 Primer.\u003c\/p\u003e\n\u003cp\u003eSome applications of NEXTITE AB422 include:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eTransport Industry: Used to bond fibreglass (FRP), metal, and composites in vehicles like trucks, buses, trailers, and railcars.\u003c\/li\u003e\n\u003cli\u003eMarine: Bonds composite hulls, decks, and marine components with strong resistance to moisture and saltwater.\u003c\/li\u003e\n\u003cli\u003eConstruction: Joins panels, facades, and modular building elements where strength and quick curing are critical.\u003c\/li\u003e\n\u003cli\u003eSignage and Displays: Bonds plastic and metal parts in signs and displays for indoor and outdoor use.\u003c\/li\u003e\n\u003cli\u003eIndustrial Equipment: Used in machinery and appliance assembly for strong, impact- and vibration-resistant joints.\u003c\/li\u003e\n\u003cli\u003eAutomotive: Bonding structural or cosmetic repair of body panels, including re-bonding fiberglass or composite components.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eVersatility of NEXTITE AB422\u003c\/h3\u003e\n\u003cp\u003eWhile bond strength is important, it’s not the only factor to consider when selecting an adhesive. Once fully cured, NEXTITE AB422 delivers a range of additional benefits that can make a real difference depending on your application.\u003c\/p\u003e\n\u003cp\u003eWhen fully cured NEXTITE AB422 can be sanded, grinded, routed and polished to get your desired finish. You can even paint over it!\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eGreat Chemical Resistance\u003c\/li\u003e\n\u003cli\u003eHigh fatigue and impact resistance\u003c\/li\u003e\n\u003cli\u003eHigh resistance to weathering\u003c\/li\u003e\n\u003cli\u003eCan be used in indoor and outdoor applications\u003c\/li\u003e\n\u003cli\u003eWaterproofing when applied correctly\u003c\/li\u003e\n\u003cli\u003eHigh Temperature resistance -40 to 140°C\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eTools and Accessories\u003c\/h3\u003e\n\u003cp\u003eNEXTITE AB422 requires the use of a compatible dual cartridge dispensing applicator and static mixer nozzles, sold separately. Both the 50mL and 490mL Cartridges use standard 10:1 Ratio dual cartridge dispensing applicators and static mixers. It is important to use the correct applicator and mixer for each cartridge size, as 10:1 ratio systems are not compatible with other ratios cartridges and accessories. Each cartridge type requires the matching dispensing applicator and static mixer designed specifically for its ratio.\u003c\/p\u003e\n\u003ch4\u003e50mL Tubes\u003c\/h4\u003e\n\u003cp\u003eDispensing Applicator: Manual 50mL 10:1 Dispensing Applicator | Manual Hand Plunger for 10:1 50mL Cartridges (for one time use)\u003c\/p\u003e\n\u003cp\u003eStatic Mixer Nozzles: 10:1 50mL Quadro B Type (Standard Tip) | 10:1 50mL Quadro B Type (Narrow Tip)\u003c\/p\u003e\n\u003ch4\u003e400mL Tubes\u003c\/h4\u003e\n\u003cp\u003eDispensing Applicator: Manual 490mL 10:1 Dispensing Applicator | Pneumatic 490mL 10:1 Dispensing Applicator | Electric 490mL 10:1 Dispensing Applicator\u003c\/p\u003e\n\u003cp\u003eExtra Static Mixer Nozzles: 10:1 490mL Quadro F Type (Green – Orange Base)\u003c\/p\u003e\n\u003ch3\u003eTechnical Highlights\u003c\/h3\u003e\n\u003ctable cellpadding=\"0\" cellspacing=\"0\" border=\"1\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eAdhesive Type\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eMethyl Methacrylate\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eColour\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eBlack\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eMix Ratio\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003e10:1\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eKey Substrates\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eMetals, Plastics and Composites\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eViscosity\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003e100,000 – 130,000 CPS\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eMaximum Gap Fill\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003e9 mm\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eWorking Time\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003e11– 13 min\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eFixture Time\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003e28 – 32 min\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eFull Strength\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003e24 hrs\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eSimilar Product\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003ePLEXUS ® MA422\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003eStrength Tests\u003c\/h3\u003e\n\u003ctable cellpadding=\"0\" cellspacing=\"0\" border=\"1\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eSubstrate\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eLap Shear Strength (psi)\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eAluminium (Grit Blasted)\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003e3200 AF\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eABS\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003e2200 CF\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003ePolycarbonate\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003e2200 SF\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\n\u003cp\u003eFRP\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd\u003e\n\u003cp\u003e2450 SF\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e** SF, AF, CF – determine how the substrate failed.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003eSF – Substrate Failure\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003eAF – Adhesion Failure\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e-        \u003c!--[endif]--\u003eCF – Cohesive Failure\u003c\/p\u003e\n\u003ch3\u003eChemical Resistance\u003c\/h3\u003e\n\u003ctable cellpadding=\"0\" cellspacing=\"0\" border=\"1\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eResistant To\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eSusceptible To\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eHydrocarbons, Salt Solutions, Acids and Bases (3-10pH)\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003ePolar Solvents, Strong Acids and Bases\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003eInstructions for use\u003c\/h3\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e1.     \u003c!--[endif]--\u003eUse a static mixer nozzle to accurately mix the contents of the 10:1 cartridge. Each cartridge includes one Static Mixer Nozzle Orange 10:1, and you can purchase more in 5, 10 and 50 packs from our store.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e2.     \u003c!--[endif]--\u003eYou will also require a 10:1 Static Mixing Dispenser to push the contents through the static mixer. This is the best way to apply it and get accurate, dependable results every time.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e3.     \u003c!--[endif]--\u003eParts to be joined should fit without forcing and be clean, it is recommended to use NEXTITE PROPREP prior to applying any product to remove any oils, dust and dirt. It is important to let out any air bubbles and ensure adhesive is fully mixed by dispensing the first part of the cartridge onto some paper. This is to make sure the two separate parts are fully mixed and is generally the first 2-3mL. Apply adhesive directly from the static mixer.\u003c\/p\u003e\n\u003cp\u003e\u003c!-- [if !supportLists]--\u003e4.     \u003c!--[endif]--\u003ePress parts together in firm contact and use a clamp to secure while the glue reacts. NEXTITE AB422 will achieve a working strength within 28-32 min and full cure strength within 24 hours. You have approximately 11-13 minutes to work with the glue before it starts to set off.\u003c\/p\u003e\n\u003cp\u003ePlease check the TDS for material suitability and strength of each bond. For a tutorial how to use please refer to our YouTube Chanel.\u003c\/p\u003e\n\u003ch3\u003eShelf Life, Storage and Pack Size\u003c\/h3\u003e\n\u003cp\u003eNEXTITE AB422 has a 12 Month Shelf Life when stored correctly.\u003c\/p\u003e\n\u003cp\u003eStore in a cool dry place out of direct sunlight, an enclosed cabinet is recommended, to extend the shelf life of this product. Keep the open container tightly closed do not leave open. \u003c\/p\u003e\n\u003cp\u003e50mL and 490mL Cartridges\u003c\/p\u003e\n\u003ch3\u003eDownloads\u003c\/h3\u003e\n\u003cp\u003eNEXTITE AB422 Technical Data Sheet | NEXTITE AB422 Material Safety Data Sheet\u003c\/p\u003e","brand":"NEXTITE","offers":[{"title":"50mL","offer_id":46853720047765,"sku":"AB422-50","price":34.15,"currency_code":"AUD","in_stock":true},{"title":"490mL","offer_id":46853720080533,"sku":"AB422-490","price":134.35,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0740\/9834\/4085\/files\/NEXTITEAB42250mL.jpg?v=1770618298"},{"product_id":"nextite-ea3200","title":"NEXTITE EA3200 Flowable Black Potting Epoxy Dual Component","description":"\u003cp\u003eNEXTITE EA3200 is a flowable, industrial-grade, two-part potting epoxy adhesive offering high strength and an extended work life. Once mixed the two parts cure at room temperature without the need for heat curing. It cures to form a semi-rigid, opaque black encapsulant that is non-corrosive to metallic components on PCBs and electronic assemblies. The fully cured epoxy adhesive provides excellent environmental and chemical resistance and acts as an electrical insulator.\u003c\/p\u003e\n\u003ch3\u003eProduct Overview\u003c\/h3\u003e\n\u003cp\u003eNEXTITE EA3200 is a high performance, flowable, two part structural epoxy adhesive engineered for potting and encapsulating electronic components, curing fully at room temperature without the need for a heat curing process. It also delivers strong, durable bonds while remaining toughened and slightly flexible, helping absorb vibration and thermal movement. This makes it suitable not only for potting applications but also as a traditional high strength structural epoxy adhesive where long term durability is critical.\u003c\/p\u003e\n\u003cp\u003eWith an extended working time of 60 minutes, NEXTITE EA3200 allows ample time for potting applications, its controlled cure profile supports larger volume pours without rushing the process to be within working time and allows for accurate positioning in complex assemblies. EA3200 is non corrosive to metallic components on PCBs and electronic assemblies.\u003c\/p\u003e\n\u003cp\u003eNEXTITE EA3200 is widely used in electronic applications including component attachment to boards, housing assembly and potting of electronics. Once cured, it provides excellent environmental, temperature and chemical resistance along with strong electrical insulation properties, ensuring dependable long term performance in demanding operating conditions.\u003c\/p\u003e\n\u003ch3\u003eApplications and Uses\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003ePotting and encapsulating of electronic components and assemblies\u003c\/li\u003e\n\u003cli\u003ePCB component bonding\u003c\/li\u003e\n\u003cli\u003eEncapsulation of sensors, relays, connectors and control modules\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eBonding electronic housings and enclosures\u003c\/li\u003e\n\u003cli\u003eStructural bonding of plastic, metal and composite parts\u003c\/li\u003e\n\u003cli\u003eImproving reliability of soldered components\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eTools and Accessories\u003c\/h3\u003e\n\u003cp\u003eNEXTITE EA3200 requires the use of a compatible dual cartridge dispensing applicator and static mixer nozzles, sold separately. Both the 50mL and 400mL Cartridges use standard 1:1 Ratio dual cartridge dispensing applicators and static mixers. It is important to use the correct applicator and mixer for each cartridge size, as 1:1 ratio systems are not compatible with other ratios cartridges and accessories. Each cartridge type requires the matching dispensing applicator and static mixer designed specifically for its ratio.\u003c\/p\u003e\n\u003ch5\u003e50mL Tubes\u003c\/h5\u003e\n\u003cp\u003eDispensing Applicator: Manual 50mL 1:1 Dispensing Applicator | Manual Hand Plunger for 1:1 50mL Cartridges (for one time use)\u003c\/p\u003e\n\u003cp\u003eStatic Mixer Nozzles: 1:1 50mL Quadro B Type (Standard Tip) | 1:1 50mL Quadro B Type (Narrow Tip) \u003c\/p\u003e\n\u003ch5\u003e400mL Tubes\u003c\/h5\u003e\n\u003cp\u003eDispensing Applicator: Manual 400mL 1:1 Dispensing Applicator | Pneumatic 400mL 1:1 Dispensing Applicator | Electric 400mL 1:1 Dispensing Applicator\u003c\/p\u003e\n\u003cp\u003eExtra Static Mixer Nozzles: 1:1 400mL Quadro F Type (Green – White Base)\u003c\/p\u003e\n\u003ch3\u003eTechnical Highlights\u003c\/h3\u003e\n\u003ctable style=\"width: 99.8811%; height: 333px;\" cellpadding=\"0\" cellspacing=\"0\" border=\"1\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.625px;\"\u003e\n\u003ctd style=\"width: 53.4004%; height: 35.625px;\" valign=\"top\" width=\"300\"\u003e\n\u003cp\u003e\u003cstrong\u003eFeature\u003c\/strong\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd style=\"width: 46.4814%; height: 35.625px;\" valign=\"top\" width=\"300\"\u003e\n\u003cp\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 35.625px;\"\u003e\n\u003ctd style=\"width: 53.4004%; height: 35.625px;\" valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eAdhesive Type\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd style=\"width: 46.4814%; height: 35.625px;\" valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eEpoxy Adhesive\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 35.625px;\"\u003e\n\u003ctd style=\"width: 53.4004%; height: 35.625px;\" valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eMixed Colour\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd style=\"width: 46.4814%; height: 35.625px;\" valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eOpaque Black\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 35.625px;\"\u003e\n\u003ctd style=\"width: 53.4004%; height: 35.625px;\" valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eMixing Ratio\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd style=\"width: 46.4814%; height: 35.625px;\" valign=\"top\" width=\"300\"\u003e\n\u003cp\u003e1:1\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 35.625px;\"\u003e\n\u003ctd style=\"width: 53.4004%; height: 35.625px;\" valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eViscosity Mixed\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd style=\"width: 46.4814%; height: 35.625px;\" valign=\"top\" width=\"300\"\u003e\n\u003cp\u003e10,000 – 13,000\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 35.625px;\"\u003e\n\u003ctd style=\"width: 53.4004%; height: 35.625px;\" valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eWorking Time\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd style=\"width: 46.4814%; height: 35.625px;\" valign=\"top\" width=\"300\"\u003e\n\u003cp\u003e60 minutes\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 35.625px;\"\u003e\n\u003ctd style=\"width: 53.4004%; height: 35.625px;\" valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eFixture Time\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd style=\"width: 46.4814%; height: 35.625px;\" valign=\"top\" width=\"300\"\u003e\n\u003cp\u003e240 minutes\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 35.625px;\"\u003e\n\u003ctd style=\"width: 53.4004%; height: 35.625px;\" valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eFull Cure\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd style=\"width: 46.4814%; height: 35.625px;\" valign=\"top\" width=\"300\"\u003e\n\u003cp\u003e24 hours\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 35.6667px;\"\u003e\n\u003ctd style=\"width: 53.4004%; height: 35.6667px;\" valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eMaximum Operating Temperature\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd style=\"width: 46.4814%; height: 35.6667px;\" valign=\"top\" width=\"300\"\u003e\n\u003cp\u003e150 °C\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003e\u003cbr\u003e\u003c\/h3\u003e\n\u003ch3\u003eInstructions for Use\u003c\/h3\u003e\n\u003ch5\u003eMixing Instructions\u003c\/h5\u003e\n\u003col\u003e\n\u003cli\u003eUse gloves to minimize skin contact. DO NOT use solvents for cleaning hands.\u003c\/li\u003e\n\u003cli\u003eTo use simply insert the cartridge into the application gun and start the plunger into the cylinders using light pressure on the trigger.\u003c\/li\u003e\n\u003cli\u003eNext, remove the cartridge cap and expel a small amount of adhesive to be sure both sides are flowing evenly and freely. If automatic mixing of resin and hardener is desired, attach the mixing nozzle to the end of the cartridge and begin dispensing the adhesive.\u003c\/li\u003e\n\u003cli\u003eFor hand mixing, expel the desired amount of the adhesive and mix thoroughly. Mix for approximately 15 seconds after a uniform colour is obtained.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch5\u003eInstructions for Potting\u003c\/h5\u003e\n\u003col\u003e\n\u003cli\u003eApply the adhesive into the area which is to be potted.\u003c\/li\u003e\n\u003cli\u003eApplication to the substrate should be made within 60 minutes. Larger quantities and\/or higher temperatures will reduce this working time.\u003c\/li\u003e\n\u003cli\u003eAllow to cure at 25°C for 24 hours for full cure. Heating up to 95°C for 2 hours, will speed up curing.\u003c\/li\u003e\n\u003cli\u003eExcess uncured adhesive can be cleaned up with ketone type solvents.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch5\u003eInstructions for Bonding\u003c\/h5\u003e\n\u003col\u003e\n\u003cli\u003eFor high strength structural bonds, removal of surface contaminates such as paint, oxide films, oils, dust, mould release agents and all other surface contaminates.\u003c\/li\u003e\n\u003cli\u003eFor maximum bond strength apply adhesive evenly to both surfaces to be joined.\u003c\/li\u003e\n\u003cli\u003eApplication to the substrates should be made within 60 minutes. Larger quantities and\/or higher temperatures will reduce this working time.\u003c\/li\u003e\n\u003cli\u003eJoin the adhesive coated surfaces and allow to cure at 25°C for 24 hours for high strength. Heat up to 95°C for 2 hours, will speed up curing.\u003c\/li\u003e\n\u003cli\u003eKeep parts from moving during cure. Contact pressure is necessary. Maximum shear strength is obtained with a 3-6 mm bond line.\u003c\/li\u003e\n\u003cli\u003eExcess uncured adhesive can be cleaned up with ketone type solvents.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eShelf Life, Storage and Pack Size\u003c\/h3\u003e\n\u003cp\u003eNEXTITE EA3200 has a 12 Month Shelf Life when stored correctly.\u003c\/p\u003e\n\u003cp\u003eStore in a cool dry place out of direct sunlight, an enclosed cabinet is recommended, to extend the shelf life of this product. Keep the open container tightly closed do not leave open. \u003c\/p\u003e\n\u003cp\u003e50mL and 400mL Cartridges.\u003c\/p\u003e\n\u003ch3\u003eDownloads\u003c\/h3\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0740\/9834\/4085\/files\/NEXTITE_EA3200_TDS.pdf?v=1772666022\" target=\"_blank\" rel=\"noopener\"\u003eNEXTITE EA3200 Technical Data Sheet\u003c\/a\u003e | NEXTITE EA3200 Material Safety Data Sheet\u003c\/p\u003e","brand":"NEXTITE Adhesives","offers":[{"title":"Default Title","offer_id":47031895031957,"sku":"NEXTITE-EA3200-50","price":44.85,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0740\/9834\/4085\/files\/NEXTITE-EA3200-50mL.jpg?v=1772672324"},{"product_id":"nextite-ab830","title":"NEXTITE AB830 Primerless Structural to Metals, Fast Cure","description":"\u003cp\u003eNEXTITE AB830 is an industrial-grade, two-part MMA adhesive offering primerless adhesion to metals, excellent fatigue resistance, high strength, fast cure time, non-sag and reliable bonding of plastics, metals, and composites with little to no surface preparation. Ideal for structural applications across multiple industries. Balanced thicker viscosity ensures smooth, precise application for diverse industrial bonding needs.\u003c\/p\u003e\n\u003ch3\u003eProduct Overview\u003c\/h3\u003e\n\u003cp\u003eNEXTITE AB830 is a high-performance, two-part methyl methacrylate (MMA) structural adhesive engineered for primerless adhesion to metals. Designed for reliable bonding of engineering plastics, metals, and composite materials, NEXTITE AB830 offers exceptional strength, toughness, fatigue and impact resistance. \u003c\/p\u003e\n\u003cp\u003eWith a fast working time of 4 to 6 minutes, this adhesive allows for efficient assembly without the need for extensive surface preparation or primers. It is particularly suited for bonding primerless to thermoplastics, powder-coated metals, raw metals, and composite assemblies where high strength and impact resistance are critical.\u003c\/p\u003e\n\u003cp\u003eUsing a primerless to metal MMA adhesive provides a fast and efficient alternative to traditional welding or mechanical fastening methods. Unlike welding, MMA adhesives do not create significant heat, which eliminates the risk of material distortion or burn through. They also allow dissimilar metals and substrates to be bonded to each other primerless. Stress is distributed evenly across the bonded area rather than concentrating it at a single point like a bolt or rivet. This results in stronger, more durable assemblies with improved vibration resistance, reduced corrosion risk and faster production times since no surface primers or complex mechanical preparation is required, can bond materials as received.\u003c\/p\u003e\n\u003cp\u003eNEXTITE AB830 delivers rapid strength development at room temperature, along with excellent toughness, fatigue resistance, and long-term durability. Its non-sag, highly thixotropic formula makes it ideal for precise application, even on vertical surfaces. It also provides high gap filling capabilities of up to 9mm. This adhesive is the go-to solution for industrial manufacturing, transportation, marine, and general assembly where consistent performance and high fatigue resistance are required. \u003c\/p\u003e\n\u003cp\u003eFor production environments where a longer fixture time is critical, NEXTITE AB832 offers the same performance and material compatibility as NEXTITE AB830 but with a reduced working time of 11 to 13 minutes and a fixture time of 28 to 32 minutes. \u003c\/p\u003e\n\u003cp\u003eFor production environments where longer working times are critical, NEXTITE AB835 offers the same performance and material compatibility as NEXTITE AB832 but with an increased working time of 55 to 65 minutes and a fixture time of 100 to 120 minutes. \u003c\/p\u003e\n\u003ch3\u003eApplications and Uses\u003c\/h3\u003e\n\u003cp\u003eNEXTITE AB830 bonds to a variety of substrates without the need for primers they include but aren’t limited to:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003ePlastics: Acrylic (PMMA), Polycarbonate (PC), Acrylonitrile Butadiene Styrene (ABS), Polyvinyl Chloride (PVC)\u003c\/li\u003e\n\u003cli\u003eMetals: Aluminium, Steel, Stainless Steel, Powder Coated Surfaces\u003c\/li\u003e\n\u003cli\u003eComposites: Fibreglass Reinforced Plastic (FRP), Carbon Fibre (CF)\u003c\/li\u003e\n\u003cli\u003eOther: Glass\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eNEXTITE AB830 will not adhere to plastics with a low surface energy such as Polypropylene (PP), Polyethylene (PE) or Polyolefins. These plastics can be structurally adhered to with NEXTITE AB206 and NEXTITE Instant Adhesives also have a great bond when using NEXTITE SP 901 Primer.\u003c\/p\u003e\n\u003cp\u003eSome applications of NEXTITE AB830 include:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eTransport Industry: Used to bond metal and composites in vehicles like trucks, buses, trailers, and railcars.\u003c\/li\u003e\n\u003cli\u003eMarine: Bonds composite hulls, decks, and marine components with strong resistance to moisture and saltwater.\u003c\/li\u003e\n\u003cli\u003eSignage and Displays: Bonds plastic and metal parts in signs and displays for indoor and outdoor use.\u003c\/li\u003e\n\u003cli\u003eIndustrial Equipment: Used in machinery and appliance assembly for strong, impact- and vibration-resistant joints.\u003c\/li\u003e\n\u003cli\u003eAutomotive: Bonding structural or cosmetic repair of body panels, including re-bonding fibreglass or composite components.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eVersatility of NEXTITE AB830\u003c\/h3\u003e\n\u003cp\u003eWhile bond strength is important, it’s not the only factor to consider when selecting an adhesive. Once fully cured, NEXTITE AB830 delivers a range of additional benefits that can make a real difference depending on your application.\u003c\/p\u003e\n\u003cp\u003eWhen fully cured NEXTITE AB830 can be sanded, grinded, routed and polished to get your desired finish. You can even paint over it!\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eGreat Chemical Resistance\u003c\/li\u003e\n\u003cli\u003eHigh fatigue and impact resistance\u003c\/li\u003e\n\u003cli\u003eHigh resistance to weathering\u003c\/li\u003e\n\u003cli\u003eCan be used in indoor and outdoor applications\u003c\/li\u003e\n\u003cli\u003eHigh Temperature resistance -50 to 120°C\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eTools and Accessories\u003c\/h3\u003e\n\u003cp\u003eNEXTITE AB830 requires the use of a compatible dual cartridge dispensing applicator and static mixer nozzles, sold separately. Both the 50mL and 490mL Cartridges use standard 10:1 Ratio dual cartridge dispensing applicators and static mixers. It is important to use the correct applicator and mixer for each cartridge size, as 10:1 ratio systems are not compatible with other ratios cartridges and accessories. Each cartridge type requires the matching dispensing applicator and static mixer designed specifically for its ratio.\u003c\/p\u003e\n\u003ch4\u003e50mL Tubes\u003c\/h4\u003e\n\u003cp\u003eDispensing Applicator: Manual 50mL 10:1 Dispensing Applicator | Manual Hand Plunger for 10:1 50mL Cartridges (for one time use)\u003c\/p\u003e\n\u003cp\u003eStatic Mixer Nozzles: 10:1 50mL Quadro B Type (Standard Tip) | 10:1 50mL Quadro B Type (Narrow Tip)\u003c\/p\u003e\n\u003ch4\u003e400mL Tubes\u003c\/h4\u003e\n\u003cp\u003eDispensing Applicator: Manual 490mL 10:1 Dispensing Applicator | Pneumatic 490mL 10:1 Dispensing Applicator | Electric 490mL 10:1 Dispensing Applicator\u003c\/p\u003e\n\u003cp\u003eExtra Static Mixer Nozzles: 10:1 490mL Quadro F Type (Green – Orange Base)\u003c\/p\u003e\n\u003ch3\u003eTechnical Highlights\u003c\/h3\u003e\n\u003ctable cellpadding=\"0\" cellspacing=\"0\" border=\"1\" style=\"width: 100.059%; height: 355.938px;\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.5938px;\"\u003e\n\u003ctd valign=\"top\" width=\"300\" style=\"width: 53.4759%; height: 35.5938px;\"\u003e\n\u003cp\u003eAdhesive Type\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\" style=\"width: 53.4759%; height: 35.5938px;\"\u003e\n\u003cp\u003eMethyl Methacrylate\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 35.5938px;\"\u003e\n\u003ctd valign=\"top\" width=\"300\" style=\"width: 53.4759%; height: 35.5938px;\"\u003e\n\u003cp\u003eColour\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\" style=\"width: 53.4759%; height: 35.5938px;\"\u003e\n\u003cp\u003eGrey\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 35.5938px;\"\u003e\n\u003ctd valign=\"top\" width=\"300\" style=\"width: 53.4759%; height: 35.5938px;\"\u003e\n\u003cp\u003eMix Ratio\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\" style=\"width: 53.4759%; height: 35.5938px;\"\u003e\n\u003cp\u003e10:1\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 35.5938px;\"\u003e\n\u003ctd valign=\"top\" width=\"300\" style=\"width: 53.4759%; height: 35.5938px;\"\u003e\n\u003cp\u003eKey Substrates\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\" style=\"width: 53.4759%; height: 35.5938px;\"\u003e\n\u003cp\u003eMetals, Plastics and Composites\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 35.5938px;\"\u003e\n\u003ctd valign=\"top\" width=\"300\" style=\"width: 53.4759%; height: 35.5938px;\"\u003e\n\u003cp\u003eViscosity\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\" style=\"width: 53.4759%; height: 35.5938px;\"\u003e\n\u003cp\u003e100,000 – 125,000 CPS\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 35.5938px;\"\u003e\n\u003ctd valign=\"top\" width=\"300\" style=\"width: 53.4759%; height: 35.5938px;\"\u003e\n\u003cp\u003eMaximum Gap Fill\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\" style=\"width: 53.4759%; height: 35.5938px;\"\u003e\n\u003cp\u003e9 mm\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 35.5938px;\"\u003e\n\u003ctd valign=\"top\" width=\"300\" style=\"width: 53.4759%; height: 35.5938px;\"\u003e\n\u003cp\u003eWorking Time\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\" style=\"width: 53.4759%; height: 35.5938px;\"\u003e\n\u003cp\u003e4 – 6 min\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 35.5938px;\"\u003e\n\u003ctd valign=\"top\" width=\"300\" style=\"width: 53.4759%; height: 35.5938px;\"\u003e\n\u003cp\u003eFixture Time\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\" style=\"width: 53.4759%; height: 35.5938px;\"\u003e\n\u003cp\u003e17 – 19 min\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 35.5938px;\"\u003e\n\u003ctd valign=\"top\" width=\"300\" style=\"width: 53.4759%; height: 35.5938px;\"\u003e\n\u003cp\u003eFull Strength\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\" style=\"width: 53.4759%; height: 35.5938px;\"\u003e\n\u003cp\u003e24 hrs\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 35.5938px;\"\u003e\n\u003ctd valign=\"top\" width=\"300\" style=\"width: 53.4759%; height: 35.5938px;\"\u003e\n\u003cp\u003eSimilar Product\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\" style=\"width: 53.4759%; height: 35.5938px;\"\u003e\n\u003cp\u003ePLEXUS ® MA830\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003eStrength Tests\u003c\/h3\u003e\n\u003ctable cellpadding=\"0\" cellspacing=\"0\" border=\"1\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eSubstrate\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eLap Shear Strength (psi)\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eAluminium (Grit Blasted)\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003e2650\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eStainless Steel\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003e2550\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eSteel\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003e2500\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eFRP\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003e1750\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003eChemical Resistance\u003c\/h3\u003e\n\u003ctable cellpadding=\"0\" cellspacing=\"0\" border=\"1\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eResistant To\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eSusceptible To\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003eHydrocarbons, Salt Solutions, Acids and Bases (3-10pH)\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd valign=\"top\" width=\"300\"\u003e\n\u003cp\u003ePolar Solvents, Strong Acids and Bases\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003eInstructions for use\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eUse a static mixer nozzle to accurately mix the contents of the 10:1 cartridge. Each cartridge includes one Static Mixer Nozzle 10:1, and you can purchase more in 5, 10 and 50 packs from our store.\u003c\/li\u003e\n\u003cli\u003eYou will also require a 10:1 Static Mixing Dispenser to push the contents through the static mixer. This is the best way to apply it and get accurate, dependable results every time.\u003c\/li\u003e\n\u003cli\u003eParts to be joined should fit without forcing and be clean, it is recommended to use NEXTITE PROPREP prior to applying any product to remove any oils, dust and dirt. It is important to let out any air bubbles and ensure adhesive is fully mixed by dispensing the first part of the cartridge onto some cardboard. This is to make sure the two separate parts are fully mixed and is generally the first 2-3mL. Apply adhesive directly from the static mixer.\u003c\/li\u003e\n\u003cli\u003ePress parts together in firm contact and use a clamp to secure while the glue reacts. NEXTITE AB832 will achieve a working strength within 28-32 min and full cure strength within 24 hours. You have approximately 11-13 minutes to work with the glue before it starts to set off.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003ePlease check the TDS for material suitability and strength of each bond. For a tutorial how to use please refer to our YouTube Chanel.\u003c\/p\u003e\n\u003ch3\u003eShelf Life, Storage and Pack Size\u003c\/h3\u003e\n\u003cp\u003eNEXTITE AB830 has a 12 Month Shelf Life when stored correctly.\u003c\/p\u003e\n\u003cp\u003eStore in a cool dry place out of direct sunlight, an enclosed cabinet is recommended, to extend the shelf life of this product. Keep the open container tightly closed do not leave open. \u003c\/p\u003e\n\u003cp\u003e50mL and 490mL Cartridges\u003c\/p\u003e\n\u003ch3\u003eDownloads\u003c\/h3\u003e\n\u003cp\u003eNEXTITE AB830 Technical Data Sheet | NEXTITE AB830 Material Safety Data Sheet\u003c\/p\u003e","brand":"NEXTITE","offers":[{"title":"50mL","offer_id":47416855068821,"sku":null,"price":36.85,"currency_code":"AUD","in_stock":true},{"title":"490mL","offer_id":47416855101589,"sku":null,"price":134.35,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0740\/9834\/4085\/files\/NEXTITEAB83050mL.jpg?v=1770618298"}],"url":"https:\/\/nextite.com.au\/collections\/automotive-transport.oembed?page=2","provider":"NEXTITE Adhesives","version":"1.0","type":"link"}