MaxBond Infusion 707 Sprayable Contact Adhesive 500mL Aerosol

Product Overview

MaxBond Infusion 707 Super Mist Spray RTM Infusion Adhesive is a mist spray adhesive developed to hold reinforcement fibres in place during RTM applications. The specially developed mist spray pattern provides a soft, non-dimpling glue line that is perfect for areas that need to maintain a smooth, aesthetic finish and won’t soak into fibres. It also maintains its tack which allows reinforcements to be repositioned if needed. 

For adhering: Composite Materials

Product Features

• Non-Chlorinated
• High Tack
• Low VOC
• Low Odour
  
• Fast Drying
• Long Open Time
• High Solids

Industries and Material Compatibility

Main Industry: Composites

Material Compatibility: Light Mats, Heavy Mats, FPR/ GRP, Carbon Fibre

Limitations: Do not use on Flexible PVC or Expanded Polystyrene

Performance

Temperature Resistance	70°C
Drying Time	30 sec
Open Time	15 min
Solids Content	33%
Spray Pattern	Mist
Colour	Clear / Colourless

Product Application

Canister

USE IN A WELL-VENTILATED AREA.

1. Surfaces to be bonded should be clean, dry, grease and dust free. If cleaning solvents are used, allow adequate time for drying and wipe surface with a clean cloth before applying adhesive.
2. Fully open the valve on the canister. Direct the gun at the surface which it is to be bonded, at a 90 degree angle. Spray adhesive 10-15cm away and apply a generous even coat of adhesive.
3. Ideal application: 10-15cm bands of adhesive overlapping by 50% spraying one surface vertically and the other horizontally. Avoid over application. Ideal coverage 80-100%. Do not concentrate in one area or allow to puddle. On porous surfaces a second coat maybe necessary (after the first coat dries apply a second coat evenly).

Aerosol Can

USE IN A WELL-VENTILATED AREA. 

1. Surfaces should be clean, dry and free from grease oil and dust.
2. Hold the aerosol at approximately 70 degrees to the surface and apply a uniform coat of adhesive to both substrates, ensuring 80-100% coverage. Spray one surface vertically, the other horizontally and pay particular attention to the edges. Porous substrates may require two applications.
3. The adhesive is ready to bond when it feels dry to the touch and does not transfer. Drying takes approximately 1-2 minutes depending on substrates, temperature and humidity. Bring the surfaces together and apply a uniform pressure over the work piece. Full cure will take 24 hours.
4. To prevent spray nozzle from blocking, at the end of each period of use, turn the can upside down and press nozzle until spray is clear of adhesive.
5. Excess adhesive can be removed with solvent cleaner removed with a suitable solvent cleaner.

Coverage

Aerosol: 10m²

Canister: 440m²

Limitations

Do not use on flexible PVC or EPS. Infusion 707 dries within 30 seconds under normal conditions but this will vary under different temperatures and humidities. High humidity and low temperatures will slow the drying time and if the temperature gets very low can produce bloom. Bloom is moisture which forms on the glue line caused by solvent evaporation lowering the air temperature above it. 

Shelf Life and Storage

Protect from extremes of temperature in a controlled environment between 15 and 35°C, and away from direct sunlight.

Do not stand on a cold concrete floor. Low temperatures can result in irreparable separation of the adhesive. If the adhesive sprays like a jet the canister is too cold, warm to at least 10°c before using. DO NOT ALLOW THE PRODUCT TO FREEZE 

Stored under the correct conditions in original unopened containers the product will have a shelf life of 18 months.

Downloads

MaxBond Infusion 707 Technical Data Sheet | MaxBond Infusion 707 Canister SDS | MaxBond Infusion 707 Aerosol SDS